SunTouch® - Pentair

More documents

Recommendations

Info

52 Mounting the SunTouch Power Center The SunTouch Power Center can be mounted on a flat vertical surface, such as a wall or post. Note: Select a convenient location to mount the SunTouch Power Center, making sure that the location is greater than 5 feet from the pool or spa and no further than 15 feet from the pool/spa valve. To mount the SunTouch Power Center: 1. Position the SunTouch Power Center against the vertical flat surface. If wall anchors are being used, support the SunTouch Power Center in position (horizontally level and square) against the surface and mark the bracket hole pattern on the wall. 2. Secure the Power Center with three (3) screws in the mounting bracket holes. If using wall anchors, use 3/16” drill and set the anchors and secure the enclosure with screws. Mounting bracket Mounting bracket Mounting bracket SunTouch Power Center Mounting Brackets SunTouch Solar, Pool and Spa Control System Installation and User’s Guide
53 Removing Electrical Conduit Knockouts Before installing SunTouch power center electrical conduit, read the following recommended guidelines. Remove the power center conduit knockouts as needed: • Determine the number of low and high voltage circuits being used in the SunTouch power center, the conduit size and runs needed based on the wire size, and the number of conductors within the conduit. • The conduit knockouts are located underneath of the SunTouch power center. There are three ½" and one ¾” conduit knockouts. It is recommended to use ¾” conduit for the main AC power conductors. • There is one 1” grommet hole located underneath the power center to access the low-voltage raceway. Use this opening for low voltage cables (sensor wires, IntelliFlo pump and IntelliChlor cables). • Follow manufactures instructions when installing and testing of ground fault circuit breakers (GFCB) and interrupters (GFCI). ¾" conduit knockout from main power supply circuit breaker (No. 14 minimum AWG wire) 1" grommet hole to low-voltage raceway for low voltage wires Three ½"conduit knockouts for relays and other equipment. SunTouch Power Center Conduit Knockouts SunTouch Solar, Pool and Spa Control System Installation and User’s Guide
Page 1 and 2:
SunTouch ® Pool, Spa and Solar Con
Page 3 and 4:
i Contents IMPORTANT WARNING AND SA
Page 5 and 6:
iii Contents Installing Valve Actua
Page 7 and 8:
v IMPORTANT WARNING AND SAFETY INST
Page 9 and 10: 1 SunTouch ® Control System Overvi
Page 11 and 12: 3 Control Buttons (Continued) ➂
Page 13 and 14: 5 Operating SunTouch in Solar Only
Page 15 and 16: 7 Solar Only Menus (Continued) Syst
Page 17 and 18: 9 Freeze Protection in Solar Only m
Page 19 and 20: 11 SunTouch Main Status Screen (Poo
Page 21 and 22: 13 Pool/Spa Mode Menus The followin
Page 23 and 24: 15 Heat Menu (2/14) (Continued) Spa
Page 25 and 26: 17 Schedules Menu (4/14) Scheduled
Page 27 and 28: 19 Clock Menu (5/14) Use the Clock
Page 29 and 30: 21 Valves Menu (7/14) The valves fe
Page 31 and 32: 23 Advanced Menu (8/14): Calibrate
Page 33 and 34: 25 Advanced Menu (8/14): Reset Fact
Page 35 and 36: 27 SunTouch Solar, Pool and Spa Con
Page 37 and 38: 29 To select a single-speed pump. M
Page 39 and 40: 31 Pump Menu (12/14) (Continued) In
Page 45 and 46: 37 IntelliChlor Menu (13/14): Statu
Page 47 and 48: 39 SunTouch Main Status Screen (Poo
Page 49 and 50: 41 Pool/Spa Mode (Single Body of Wa
Page 51 and 52: 43 SunTouch Solar Package Contents
Page 53 and 54: 45 SunTouch Power Center (Front Vie
Page 55 and 56: 47 8 9 Plumb the solar feed and ret
Page 57 and 58: 49 SunTouch Power Center High Volta
Page 59: 51 Preparing the SunTouch Power Cen
Page 63 and 64: 55 Transformer Connections High Vol
Page 65 and 66: 57 Accessing the SunTouch Motherboa
Page 67 and 68: 59 Installing relays (Continued) St
Page 69 and 70: 61 Installing and Connecting Temper
Page 71 and 72: 63 Connecting to a Sta-Rite ® Gas
Page 73 and 74: 65 SunTouch Pool/Spa Controller Sys
Page 75 and 76: 67 Connecting IntelliChem to the Su
Page 77 and 78: 69 SunTouch Error Messages Error Me
Page 79 and 80: 71 Temperature vs. Resistance Data
Page 81 and 82: 73 SunTouch Solar, Pool and Spa Con
Page 83 and 84: 75 Wiring SunTouch to the IntelliCh
Page 85 and 86: 77 Wiring IntellilChlor (SCG) and I
Page 87 and 88: 79 Installing the ESO Circuit Board
Page 89 and 90: 81 Commercial Application using ESO
Page 91 and 92: How to BACKWASH Your Filter When yo
show all

SunTouch® - Pentair

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?