V750-series UHF RFID System User's Manual - PLCeasy

More documents

Recommendations

Info

The format of status judgment expression 1) If the NML mode is specified in output function setting, you can set conditions by using the following format. Condition A Condition B Comparison symbol data “DAT”: data to be read “TCT”: tag count to be read Comparison operators (1) When comparison symbol data is “DAT”: “==”: Left side data is equal to right side data. ”!=”: Left side data is not equal to right side data. Comparison data (2) When comparison symbol data is “TCT”: “==”: Left side data is equal to right side data. ”!=”: Left side data is not equal to right side data. “>=”: Left side data is bigger than right side data. ”
(1) Set Operation (SETO) This command is to write operation conditions into the nonvolatile memories in the reader. The new setting shall be enabled at the upcoming startup. Command SETO(S)Param1=Value1 Response Note: ・ Putting equal between a single setting item and a setting value specifies the value (no need to put ‘-‘ before setting item). ・ Multiple setting items can not be applicable. SETO[RC] [RC]: Response Code *(S) Space Character Example 1) When the Response I/F after command execution is set RS-232C: [Tx] SETO rif=2 [Rx] SETO0000 Example 2) When the executed command at the start up is set as [“RDID -ant 122322 -tmo 100”]: [Tx] SETO iec=1 "RDID -ant 122322 -tmo 100" [Rx] SETO0000 Example 3) When Input 1 function setting is set as [Command execution, start up edge, "RDID -ant 122322 - tmo 100"] : [Tx] SETO in1=1 0 "RDID -ant 122322 -tmo 100" [Rx] SETO0000 Example 4) When output 3 function setting is set as [Signal is on for 2 seconds] when the executed command is finished normally, the read data is 12bytes(24characters) and the 5 th to 8 th data is “0000”: [Tx] SETO ot3=31 2000 dat==****0000**************** [Rx] SETO0000 Example 5) When output 4 function setting is set as[Signal is on for 1 second] if tag count is 10 or less: [Tx] SETO ot4=31 1000 TCT
Page 1 and 2:
V750-series UHF RFID System User’
Page 3 and 4:
Declarations EQUIPMENT MODIFICATION
Page 5 and 6:
警 WARNING Never disassemble, repa
Page 7 and 8:
Do not allow the device or cables t
Page 9 and 10:
Table of Contents Feature of V750 s
Page 11 and 12:
Feature of V750 series RFID system
Page 13 and 14:
Main Features (1) Well-tuned commun
Page 15 and 16:
• Interference from other antenna
Page 17 and 18:
1.2.3 Characteristics Characteristi
Page 19 and 20:
1.3.3 Setting the reader RF Power D
Page 21 and 22:
1. Hold the antenna in its mounting
Page 23 and 24:
1.4.4 DC Power Input The Reader is
Page 25 and 26:
1.4.4 Antenna Port One to four OMRO
Page 27 and 28:
1.4.5 Status Indicators Status Indi
Page 29 and 30:
1.4.6 I/O Interface As an input/out
Page 31 and 32:
Example of the wiring with peripher
Page 33 and 34: Example of the wiring with peripher
Page 35 and 36: Connecting to the PC: Serial settin
Page 37 and 38: 2. Functions and Control Reference
Page 39 and 40: 2.2.2 Reader Configuration In some
Page 41 and 42: 2.3 Functions 2.3.1 Command Executi
Page 43 and 44: (2) Reader status output Data is ou
Page 45 and 46: 2.4.2 Communication Sequence As a w
Page 47 and 48: A sequence when the period is not s
Page 49 and 50: 3) Multi Once The reader reads mult
Page 51 and 52: 2.4.3 Antenna Sequence The reader c
Page 53 and 54: 2.4.5 Communication Data Control (1
Page 55 and 56: 2.5 Tag Fundamentals Tag Memory Str
Page 57 and 58: Response frame for Ethernet Termina
Page 59 and 60: 3.1.2 Command Code List Following i
Page 61 and 62: Category Tag communicat ion error S
Page 63 and 64: Command Code, Response Code and Res
Page 65 and 66: To set parameters, items in the fol
Page 67 and 68: [Note] For setting a timeout value,
Page 69 and 70: (2) Write ID (WTID) Command WTID(S)
Page 71 and 72: (4) Write Data (WTDT) Command WTDT(
Page 73 and 74: (6) Kill (KILL) Command Response *(
Page 75 and 76: Reader Settings [Ethernet] (GETR/SE
Page 77 and 78: (2) Get Reader (GETR) This command
Page 79 and 80: (Smoothing buffer size) -Max: 999 -
Page 81 and 82: (3) SAVE communication setting (SAV
Page 83: Operation Settings [Programmable Ou
Page 87 and 88: 3.1.5.5 Control Command (1) Initial
Page 89 and 90: (3) External Input Output control (
Page 91 and 92: (5) Good Bye (GBYE) - Shut down con
Page 93 and 94: (7) Test System (TEST) This command
Page 95 and 96: 3.2 Examples Examples given in this
Page 97 and 98: 3.2.4 Example 4 Automated pass chec
Page 99 and 100: 3.2.5 Example 5 Auto sorting with c
Page 101 and 102: 4.2 Operation Mode 4.2.1 Page List
Page 103 and 104: Description of Each Item Item Descr
Page 105 and 106: 4.2.3 Reader Settings Function In t
Page 107 and 108: Errors 1) Invalid Parameter(s) in [
Page 109 and 110: Description of Each Item RF Control
Page 111 and 112: 4.2.5 Operation Settings Function I
Page 113 and 114: Action [Save] To change the operati
Page 115 and 116: Action To set typical options on th
Page 117 and 118: Action [Start] To display the lates
Page 119 and 120: [Stop] To stop obtaining the histor
Page 121 and 122: Errors 1) Can Not Connect It means
Page 123 and 124: 4.3 Safe Mode Safe Mode is used for
Page 125 and 126: 4.3.2 Firmware Update Page Function
Page 127 and 128: Errors 1) Illegal File Format. Conf
Page 129 and 130: 5.2 Communications Time The followi
Page 131 and 132: APPENDIX: OUTLINE DRAWINGS Reader /
Page 133 and 134: Antenna Cable: (V740-A01-3.0M, V740
Page 135:
OMRON CORPORATION RFID BUSINESS DEV
show all

V750-series UHF RFID System User's Manual - PLCeasy

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?