QUICK & CRASH - The International Arcade Museum

More documents

Recommendations

Info

4. Replace the Gun Switch, Trigger or Lens and reassemble in reverse order. Note: If the Fibre Optic Holder has come off, reattach it by aligning the marking on the Fibre Optic Holder with the marking on the Gun Side (L). Install the Lens so that the convex (curved) surface is facing outward. White Marking Lens Fibre Optic Holder Gun Side (L) Gun Side (L) Fibre Optic Holder White Marking Page 100
7-35 Replacing the Gun Harness Assy 1. Remove the Fibre Optic Cable. (See section 7-30 page 93) 2. Remove 2off cap bolts (M3x6) and remove the Harness Guide from the Pipe Bracket. 3. Remove 1off Pozi head screw (M5x20), Hex nut (M5) and unfasten the Pipe Clip and Pipe Bracket. Harness Guide O Ring Pipe Bracket Pipe Clip Hex Nut (M5) Pozi Head Screw (M5x20) 4. Remove 1off cap bolt (M3x20), 1off cap bolt (M3x8), 2off hex nut (M3) and remove the Hand Protectors (L) and (R). Hex Nut (M3) Hand Protector (L) Cap Bolt (M3x8) Hand Protector (R) Cap Bolt (M3x20) Page 101
Page 1 and 2:
QUICK & CRASH OPERATORS MANUAL IT I
Page 3 and 4:
7. MAINTENANCE ....................
Page 5 and 6:
NOTES ON INSTALLATION NEVER turn th
Page 7 and 8:
HINWEISE ZUR AUFSTELLUNG NIEMALS da
Page 9 and 10:
PUNKTER OM INSTALLATION Tænd aldri
Page 11 and 12:
NOTAS DE INSTALACIÓN. JAMÁS ENCIE
Page 13 and 14:
NOTES D’INSTALLATION NE JAMAIS me
Page 15 and 16:
ΣΗΜΕΙΩΣΕΙΣ ΓΙΑ ΤΗΝ
Page 17 and 18:
NOTES D’INSTALLATION NON ACCENDER
Page 19 and 20:
MERKNADER VED INSTALLASJON Slå ALD
Page 21 and 22:
Opmerkingen aangaande Installatie S
Page 23 and 24:
NOTAS SOBRE A INSTALAÇÃO NUNCA li
Page 25 and 26:
ATT BEAKTA VID INSTALLATION Sätt a
Page 27 and 28:
ASENNUSHUOMIOITA Älä koskaan kytk
Page 29 and 30:
2. HOW TO PLAY Game Description Thi
Page 31 and 32:
4. MOVING THE MACHINE This equipmen
Page 33 and 34:
CETTE MACHINE EST DESTINEE UNIQUEME
Page 35 and 36:
5-1 Joining the Front and Rear Cabi
Page 37 and 38:
5-2 Removing the Flat Target Packin
Page 39 and 40:
6-1 Adjustment Switches The Adjustm
Page 41 and 42:
6-2-2 Ticket Payout Setting n Do no
Page 43 and 44:
6-4 Adjusting the Launcher Solenoid
Page 45 and 46:
6-6 Adjusting the Flat Target (U)/(
Page 47 and 48:
O Aanpassingen of onderhoud aan dez
Page 49 and 50: 7-1-3 Cleaning the Cup Target Senso
Page 51 and 52: 7-1-5 Cleaning the Fibre Optic Cabl
Page 53 and 54: 7-2 Replacing the Game PC Board Not
Page 55 and 56: 7-4 Replacing the Rear Glass 1. Rem
Page 57 and 58: 7-6 Replacing the Rear Fluorescent
Page 59 and 60: 4. Remove the 4off Security screws
Page 61 and 62: 4. Hold the mirror both top and bot
Page 63 and 64: 3. Remove 6off pozi head screws (M4
Page 65 and 66: 3. Only loosen 2off Pozi flange hea
Page 67 and 68: 5. Remove 3off Pozi head head screw
Page 69 and 70: 7-13 Replacing the Header Lamp 1. R
Page 71 and 72: 4. Disconnect the connectors (CN45
Page 73 and 74: 7-16 Replacing the Launcher Sensor
Page 75 and 76: 4. To remove the solenoid plunger r
Page 77 and 78: 7-18 Removing the Flat Target Assem
Page 79 and 80: 4. To remove the solenoid plunger,
Page 81 and 82: 7-21 Replacing the Flat Target Moto
Page 83 and 84: 7-22 Replacing the Flat Target Sens
Page 85 and 86: 7-24 Replacing the Flat Target Sens
Page 87 and 88: 7-26 Replacing the Gun Detection Se
Page 89 and 90: 7-27 Replacing the [SET] and [START
Page 91 and 92: 3. Remove the 4off Self Tapping scr
Page 93 and 94: 7-30 Replacing the Xenon PC Board C
Page 95 and 96: 5. Reassemble in reverse order. Not
Page 97 and 98: 7-32 Removing the Xenon Fan and Fil
Page 99: 7-34 Replacing the Gun Switch, Trig
Page 103 and 104: 10 Reassemble in reverse order. Not
Page 105 and 106: Page 105
Page 107 and 108: Item Description Part No 1 Gun Moun
Page 109 and 110: Item Description Part No 1 Front Pe
Page 111 and 112: Item Description Part No 41 Fluores
Page 113 and 114: Xenon Assembly 11 1 6 8 2 3 4 7 9 1
Page 115 and 116: Item Cup Description Explosion Mech
Page 117 and 118: Item Description Part No Flat Targe
Page 119 and 120: Item Description Part No 33 Base (U
Page 121 and 122: Item Description Part No Flat Targe
Page 123 and 124: Item Description Part No 33 Base (L
Page 125 and 126: Item Shutter Assembly - Complete De
Page 127 and 128: Item Description Part No 1 G rip (L
Page 129 and 130: 10. SCHEMATICS Page 129
Page 131: For all Parts or Technical Support
show all

QUICK & CRASH - The International Arcade Museum

Create successful ePaper yourself

Delete template?

Save as template?