QUICK & CRASH - The International Arcade Museum

More documents

Recommendations

Info

7-17 Replacing the Shutter Solenoid 1. Remove the Front Maintenance Door from the Target Cabinet (See section 7-10 page 64). 2. Disconnect connector (CN28). 3. Remove 4off socket flange screws (M5x8) and remove the Shutter Solenoid. Socket Flange Screw (M5x8) Ring Tag Connector (CN28) Shutter Solenoid Spacer (6dia x 5) Solenoid Plunger Spacer (6dia x 10) Spacers (6dia x 5) Solenoid Shaft#2 Tension Spring Spring Supports Solenoid Springs Page 74
4. To remove the solenoid plunger remove one of the E-Clips from the solenoid shaft#2, the flat washer (M6) and spacer (6dia x 5). Withdraw the solenoid shaft#2 releasing the solenoid springs, tension spring, spacers (6dia x 10), and delrin washers. Install the solenoid spring (S) so the spring hook comes in contact with the side of the spacer (6dia x 5) Delrin Washer Solenoid Plunger Flat Washer (M6) E-clip Spacer (6dia x 5) Solenoid Shaft Spring Hook Solenoid Spring Spacer (6dia x 10) Tension Spring Note: <strong>The</strong> solenoid springs are wound in different directions. When refitting the solenoid springs ensure that the hook of the spring is in contact with the space (6dia x 5). After replacing the shutter solenoid, it is recommended that a good quality Silicone Grease is applied to the solenoid shaft#2 and to the supports for the solenoid and tension springs. After replacing the solenoid, ensure that the solenoid position is adjusted correctly. (See section 6-5 page 44) Page 75
Page 1 and 2:
QUICK & CRASH OPERATORS MANUAL IT I
Page 3 and 4:
7. MAINTENANCE ....................
Page 5 and 6:
NOTES ON INSTALLATION NEVER turn th
Page 7 and 8:
HINWEISE ZUR AUFSTELLUNG NIEMALS da
Page 9 and 10:
PUNKTER OM INSTALLATION Tænd aldri
Page 11 and 12:
NOTAS DE INSTALACIÓN. JAMÁS ENCIE
Page 13 and 14:
NOTES D’INSTALLATION NE JAMAIS me
Page 15 and 16:
ΣΗΜΕΙΩΣΕΙΣ ΓΙΑ ΤΗΝ
Page 17 and 18:
NOTES D’INSTALLATION NON ACCENDER
Page 19 and 20:
MERKNADER VED INSTALLASJON Slå ALD
Page 21 and 22:
Opmerkingen aangaande Installatie S
Page 23 and 24: NOTAS SOBRE A INSTALAÇÃO NUNCA li
Page 25 and 26: ATT BEAKTA VID INSTALLATION Sätt a
Page 27 and 28: ASENNUSHUOMIOITA Älä koskaan kytk
Page 29 and 30: 2. HOW TO PLAY Game Description Thi
Page 31 and 32: 4. MOVING THE MACHINE This equipmen
Page 33 and 34: CETTE MACHINE EST DESTINEE UNIQUEME
Page 35 and 36: 5-1 Joining the Front and Rear Cabi
Page 37 and 38: 5-2 Removing the Flat Target Packin
Page 39 and 40: 6-1 Adjustment Switches The Adjustm
Page 41 and 42: 6-2-2 Ticket Payout Setting n Do no
Page 43 and 44: 6-4 Adjusting the Launcher Solenoid
Page 45 and 46: 6-6 Adjusting the Flat Target (U)/(
Page 47 and 48: O Aanpassingen of onderhoud aan dez
Page 49 and 50: 7-1-3 Cleaning the Cup Target Senso
Page 51 and 52: 7-1-5 Cleaning the Fibre Optic Cabl
Page 53 and 54: 7-2 Replacing the Game PC Board Not
Page 55 and 56: 7-4 Replacing the Rear Glass 1. Rem
Page 57 and 58: 7-6 Replacing the Rear Fluorescent
Page 59 and 60: 4. Remove the 4off Security screws
Page 61 and 62: 4. Hold the mirror both top and bot
Page 63 and 64: 3. Remove 6off pozi head screws (M4
Page 65 and 66: 3. Only loosen 2off Pozi flange hea
Page 67 and 68: 5. Remove 3off Pozi head head screw
Page 69 and 70: 7-13 Replacing the Header Lamp 1. R
Page 71 and 72: 4. Disconnect the connectors (CN45
Page 73: 7-16 Replacing the Launcher Sensor
Page 77 and 78: 7-18 Removing the Flat Target Assem
Page 79 and 80: 4. To remove the solenoid plunger,
Page 81 and 82: 7-21 Replacing the Flat Target Moto
Page 83 and 84: 7-22 Replacing the Flat Target Sens
Page 85 and 86: 7-24 Replacing the Flat Target Sens
Page 87 and 88: 7-26 Replacing the Gun Detection Se
Page 89 and 90: 7-27 Replacing the [SET] and [START
Page 91 and 92: 3. Remove the 4off Self Tapping scr
Page 93 and 94: 7-30 Replacing the Xenon PC Board C
Page 95 and 96: 5. Reassemble in reverse order. Not
Page 97 and 98: 7-32 Removing the Xenon Fan and Fil
Page 99 and 100: 7-34 Replacing the Gun Switch, Trig
Page 101 and 102: 7-35 Replacing the Gun Harness Assy
Page 103 and 104: 10 Reassemble in reverse order. Not
Page 105 and 106: Page 105
Page 107 and 108: Item Description Part No 1 Gun Moun
Page 109 and 110: Item Description Part No 1 Front Pe
Page 111 and 112: Item Description Part No 41 Fluores
Page 113 and 114: Xenon Assembly 11 1 6 8 2 3 4 7 9 1
Page 115 and 116: Item Cup Description Explosion Mech
Page 117 and 118: Item Description Part No Flat Targe
Page 119 and 120: Item Description Part No 33 Base (U
Page 121 and 122: Item Description Part No Flat Targe
Page 123 and 124: Item Description Part No 33 Base (L
Page 125 and 126:
Item Shutter Assembly - Complete De
Page 127 and 128:
Item Description Part No 1 G rip (L
Page 129 and 130:
10. SCHEMATICS Page 129
Page 131:
For all Parts or Technical Support
show all

QUICK & CRASH - The International Arcade Museum

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?