Inogen One G3 Technical Manual

More documents

Recommendations

Info

3. Test the function of each button and the LCD. If anything does not work, reseat the cables in the connectors and check for debris in the connectors. 4. Re-install the four screws that connect the user interface panel to the chassis (Figures 5 and 6). Tighten screws to 6 in-lbs. 5. Place the device on its back side. 6. Seat the feet of the front housing into the corresponding grooves on the chassis (Figure 10) then push down and toward the device to secure the housing in the chassis. Figure 10: Housing feet and corresponding chassis grooves 7. Place the device on its front side and repeat step 2 to secure the back housing into the chassis. 8. Replace the two screws that connect the back housing to the chassis and the two screws that connect the front housing to the chassis (Figures 2 and 4). Tighten screws to 6 in-lbs. 9. Return the concentrator to the upright position 10. Slide the battery back into the chassis. Ensure the battery clip is fully seated. 96-03997-00-01 revA Service Manual, Inogen One G3 - 124 -
SP-520 Inogen One G3 Dual Feed Tube Replacement Parts Required: 1. SP-520, Dual Feed Tube Tools Required: 1. T10 Torx Driver 2. Small Flathead Screw Driver 3. Pliers Notes: 1. When removing screws from the device carefully set in a bin or secure area as these screws will be used to secure the replacement parts. 2. Many of the screws used on the Inogen One G3 have pre-applied loctite on the threads. These loctite screws can be re-used up to four times before replacement screws are required (If exceeded four uses please contact Inogen for a screw replacement kit). Instructions for Removing the Housing: 1. While facing the front housing, remove the battery from the concentrator by pushing down on the blue battery release clip and sliding the device away (Figure 1). Figure 1: Direction to slide device to remove battery 96-03997-00-01 revA Service Manual, Inogen One G3 - 125 -
Page 1 and 2:
INOGEN ONE G3 OXYGEN CONCENTRATOR S
Page 3 and 4:
SP-501 and SP-502 Inogen One G3 Fro
Page 5 and 6:
Figure 4: Location of screws 5. Sli
Page 7 and 8:
2. To remove the back housing, plac
Page 9 and 10:
Figure 6: Location of front screws
Page 11 and 12:
3. Re-install the two screws securi
Page 13 and 14:
Parts Required: 1. SP-504, LCD Tool
Page 15 and 16:
Page 17 and 18:
Cannula tube LCD cable Figure 8: Re
Page 19 and 20:
Figure 11: Housing feet and corresp
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Figure 10: Inlet T tube and inlet u
Page 27 and 28:
SP-506 Inogen One G3 Exhaust T Tube
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Figure 2: Filter box lid screws 3.
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Figure 10: Location of rear filter
Page 43 and 44:
Compressor cable Exhaust tube Figur
Page 45 and 46:
5. Plug the other end of the dual f
Page 47 and 48:
SP-509 Inogen One G3 Compressor Rep
Page 49 and 50:
Figure 4: Filter box lid screws 3.
Page 51 and 52:
Compressor cable Exhaust tube Figur
Page 53 and 54:
SP-510 Inogen One G3 Power Cable Re
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Figure 1: Direction to slide device
Page 63 and 64:
Figure 5: Location of rear screws F
Page 65 and 66:
Figure 9: Manifold bracket screw 2.
Page 67 and 68:
Instructions for Replacing the Hous
Page 69 and 70:
Page 71 and 72:
Page 73 and 74: Exhaust T tube Manifold screws Inta
Page 75 and 76: SP-513 Inogen One G3 Accumulator Re
Page 77 and 78: Figure 4: Location of screws 5. Sli
Page 79 and 80: Cannula tube LCD cable Figure 8: Re
Page 81 and 82: Figure 12: Properly installed accum
Page 83 and 84: SP-514 Inogen One G3 Breath Detect
Page 87 and 88: Cannula tube LCD cable Figure 8: Re
Page 89 and 90: O2 sensor tubing Accumulator tubing
Page 91 and 92: Figure 16: Housing feet and corresp
Page 93 and 94: Figure 1: Direction to slide device
Page 95 and 96: Figure 6: Location of front screws
Page 97 and 98: Figure 10: Screws to be removed fro
Page 101 and 102: 2. To remove the back housing, plac
Page 103 and 104: Figure 6: Filter box lid screws 3.
Page 105 and 106: Instructions for Replacing the Hous
Page 109 and 110: Parts Required: 1. SP-518, Muffler
Page 111 and 112: Figure 3: Direction to slide housin
Page 113 and 114: Figure 7: Unplug UIP cable from mot
Page 115 and 116: Figure 11: Product manifold motherb
Page 117 and 118: 3. Replace the product manifold. Ma
Page 119 and 120: SP-519 Inogen One G3 LCD Cable Repl
Page 123: Cannula tube LCD cable Figure 8: Re
Page 129 and 130: Feed tube and inlet union Figure 8:
Page 131 and 132: Figure 13: Properly installed dual
Page 135 and 136: Figure 2: Location of screws 3. Wit
Page 137 and 138: Figure 6: Spring and spring nest as
Page 139 and 140: SP-522 Inogen One G3 Column Recepta
Page 141 and 142: Column latch Figure 4: Location of
Page 143 and 144: 7. Assure both lower grommets are i
Page 145 and 146: SP-523 Inogen One G3 Chassis Replac
Page 147 and 148: Figure 3: Chassis gasket 8. See “
Page 149 and 150: Inogen One G3 Troubleshooting Guide
Page 151 and 152: The battery icon on the LCD shows t
Page 153 and 154: O2 Delivery Error No Error Message
show all

Inogen One G3 Technical Manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?