Inogen One G3 Technical Manual

More documents

Recommendations

Info

Figure 1: Lower grommet 3. See “SP-522 Inogen One G3 Column Receptacle Replacement” for instructions on removing the column receptacles, attached tubing, columns, and tube bracket. Also remove the receptacle washers from the housing (Figure 2). Figure 2: Receptacle washer 4. See “SP-521 Inogen One G3 Column Latch Replacement” for instructions on removing the column latches. 5. See “SP-503 Inogen One G3 User interface Panel Replacement” for instructions on removing the user interface panel. 6. See “SP-515 Inogen One G3 Motherboard Replacement” for instructions on removing the motherboard. 7. Remove chassis gasket from back of chassis (Figure 3). 96-03997-00-01 revA Service Manual, Inogen One G3 - 146 -
Figure 3: Chassis gasket 8. See “SP-518 Inogen One G3 Muffler Replacement” for instructions on removing the muffler and product manifold. There is no need to disconnect the lower exhaust tube from the muffler. These parts can be installed on the new chassis as one unit. 9. See “SP-513 Inogen One G3 Accumulator Replacement” for instructions on removing the accumulator. 10. See “SP-512 Inogen One G3 Feed Waste Manifold Replacement” for instructions on removing the feed waste manifolds. Do not disconnect the feed waste manifolds from their tubing. Remove the feed waste manifolds, exhaust T tube, and upper feed tube as a single unit. The exhaust T tube should be free for removal but the upper feed tube can be removed from the device by disconnecting it from the inlet union (Figure 4). Figure 4: Remove upper feed tube from inlet union 11. See “SP-508 Inogen One G3 Fan Replacement” for instructions on removing the fan, compressor, filter body, filter assembly and all attached tubing. There is no need to detach the inlet union from the dual feed tube. These parts can be installed on the new chassis as one unit. 96-03997-00-01 revA Service Manual, Inogen One G3 - 147 -
Page 1 and 2:
INOGEN ONE G3 OXYGEN CONCENTRATOR S
Page 3 and 4:
SP-501 and SP-502 Inogen One G3 Fro
Page 5 and 6:
Figure 4: Location of screws 5. Sli
Page 7 and 8:
2. To remove the back housing, plac
Page 9 and 10:
Figure 6: Location of front screws
Page 11 and 12:
3. Re-install the two screws securi
Page 13 and 14:
Parts Required: 1. SP-504, LCD Tool
Page 15 and 16:
Page 17 and 18:
Cannula tube LCD cable Figure 8: Re
Page 19 and 20:
Figure 11: Housing feet and corresp
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Figure 10: Inlet T tube and inlet u
Page 27 and 28:
SP-506 Inogen One G3 Exhaust T Tube
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Figure 2: Filter box lid screws 3.
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Figure 10: Location of rear filter
Page 43 and 44:
Compressor cable Exhaust tube Figur
Page 45 and 46:
5. Plug the other end of the dual f
Page 47 and 48:
SP-509 Inogen One G3 Compressor Rep
Page 49 and 50:
Figure 4: Filter box lid screws 3.
Page 51 and 52:
Compressor cable Exhaust tube Figur
Page 53 and 54:
SP-510 Inogen One G3 Power Cable Re
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Figure 1: Direction to slide device
Page 63 and 64:
Figure 5: Location of rear screws F
Page 65 and 66:
Figure 9: Manifold bracket screw 2.
Page 67 and 68:
Instructions for Replacing the Hous
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Exhaust T tube Manifold screws Inta
Page 75 and 76:
SP-513 Inogen One G3 Accumulator Re
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Figure 12: Properly installed accum
Page 83 and 84:
SP-514 Inogen One G3 Breath Detect
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
O2 sensor tubing Accumulator tubing
Page 91 and 92:
Page 93 and 94:
Figure 1: Direction to slide device
Page 95 and 96: Figure 6: Location of front screws
Page 97 and 98: Figure 10: Screws to be removed fro
Page 99 and 100: Figure 13: Housing feet and corresp
Page 101 and 102: 2. To remove the back housing, plac
Page 103 and 104: Figure 6: Filter box lid screws 3.
Page 105 and 106: Instructions for Replacing the Hous
Page 107 and 108: Figure 2: Location of screws 3. Sli
Page 109 and 110: Parts Required: 1. SP-518, Muffler
Page 111 and 112: Figure 3: Direction to slide housin
Page 113 and 114: Figure 7: Unplug UIP cable from mot
Page 115 and 116: Figure 11: Product manifold motherb
Page 117 and 118: 3. Replace the product manifold. Ma
Page 119 and 120: SP-519 Inogen One G3 LCD Cable Repl
Page 123 and 124: Cannula tube LCD cable Figure 8: Re
Page 125 and 126: SP-520 Inogen One G3 Dual Feed Tube
Page 129 and 130: Feed tube and inlet union Figure 8:
Page 131 and 132: Figure 13: Properly installed dual
Page 133 and 134: Figure 16: Housing feet and corresp
Page 135 and 136: Figure 2: Location of screws 3. Wit
Page 137 and 138: Figure 6: Spring and spring nest as
Page 139 and 140: SP-522 Inogen One G3 Column Recepta
Page 141 and 142: Column latch Figure 4: Location of
Page 143 and 144: 7. Assure both lower grommets are i
Page 145: SP-523 Inogen One G3 Chassis Replac
Page 149 and 150: Inogen One G3 Troubleshooting Guide
Page 151 and 152: The battery icon on the LCD shows t
Page 153 and 154: O2 Delivery Error No Error Message
show all

Inogen One G3 Technical Manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?