Inogen One G3 Technical Manual

More documents

Recommendations

Info

Product manifold tubing Figure 10: Accumulator tubing for removal 4. Remove the accumulator from the device. Instructions for Replacing the Accumulator: 1. Before installing the new accumulator, string a new zip tie through the loop in the chassis as shown in figure 11. Figure 11: Zip tie properly oriented in chassis 2. Plug the tubing on the new accumulator into its quick connect on the product manifold (Figure 10). Place the new accumulator in its designated space and tighten the zip tie around the accumulator so that the end of the zip tie is nearest the oxygen sensor tube away from the breath detect sensor. Cut off the excess zip tie (Figure 12). 96-03997-00-01 revA Service Manual, Inogen One G3 - 80 -
Figure 12: Properly installed accumulator 3. Plug the smaller motherboard tube back into its quick connect on the accumulator cap. 4. Make sure all tubes are properly oriented before reinstalling the tube bracket and the two screws that attach it to the chassis (Figure 9). Tighten screws to 6 in-lbs. Instructions for Replacing the Housing: 1. To re-install the user interface panel, plug the LCD cable back into the motherboard (Figure 8). Note orientation of red wire. Re-attach the cannula tubing to the cannula connector. 2. Reconnect the UIP cable to the motherboard (Figure 7). 3. Test the function of each button and the LCD. If anything does not work, reseat the cables in the connectors and check for debris in the connectors. 4. Re-install the four screws that connect the user interface panel to the chassis (Figures 5 and 6). Tighten screws to 6 in-lbs. 5. Place the device on its back side. 6. Seat the feet of the front housing into the corresponding grooves on the chassis (Figure 13) then push down and toward the device to secure the housing in the chassis. 96-03997-00-01 revA Service Manual, Inogen One G3 - 81 -
Page 1 and 2:
INOGEN ONE G3 OXYGEN CONCENTRATOR S
Page 3 and 4:
SP-501 and SP-502 Inogen One G3 Fro
Page 5 and 6:
Figure 4: Location of screws 5. Sli
Page 7 and 8:
2. To remove the back housing, plac
Page 9 and 10:
Figure 6: Location of front screws
Page 11 and 12:
3. Re-install the two screws securi
Page 13 and 14:
Parts Required: 1. SP-504, LCD Tool
Page 15 and 16:
Figure 4: Location of screws 5. Sli
Page 17 and 18:
Cannula tube LCD cable Figure 8: Re
Page 19 and 20:
Figure 11: Housing feet and corresp
Page 21 and 22:
2. To remove the back housing, plac
Page 23 and 24:
Figure 6: Location of front screws
Page 25 and 26:
Figure 10: Inlet T tube and inlet u
Page 27 and 28:
SP-506 Inogen One G3 Exhaust T Tube
Page 29 and 30: Figure 4: Location of screws 5. Sli
Page 31 and 32: Cannula tube LCD cable Figure 8: Re
Page 33 and 34: Figure 11: Housing feet and corresp
Page 35 and 36: Figure 2: Filter box lid screws 3.
Page 37 and 38: 2. To remove the back housing, plac
Page 39 and 40: Figure 6: Location of front screws
Page 41 and 42: Figure 10: Location of rear filter
Page 43 and 44: Compressor cable Exhaust tube Figur
Page 45 and 46: 5. Plug the other end of the dual f
Page 47 and 48: SP-509 Inogen One G3 Compressor Rep
Page 51 and 52: Compressor cable Exhaust tube Figur
Page 53 and 54: SP-510 Inogen One G3 Power Cable Re
Page 61 and 62: Figure 1: Direction to slide device
Page 63 and 64: Figure 5: Location of rear screws F
Page 65 and 66: Figure 9: Manifold bracket screw 2.
Page 67 and 68: Instructions for Replacing the Hous
Page 73 and 74: Exhaust T tube Manifold screws Inta
Page 75 and 76: SP-513 Inogen One G3 Accumulator Re
Page 79: Cannula tube LCD cable Figure 8: Re
Page 83 and 84: SP-514 Inogen One G3 Breath Detect
Page 89 and 90: O2 sensor tubing Accumulator tubing
Page 93 and 94: Figure 1: Direction to slide device
Page 97 and 98: Figure 10: Screws to be removed fro
Page 105 and 106: Instructions for Replacing the Hous
Page 109 and 110: Parts Required: 1. SP-518, Muffler
Page 111 and 112: Figure 3: Direction to slide housin
Page 113 and 114: Figure 7: Unplug UIP cable from mot
Page 115 and 116: Figure 11: Product manifold motherb
Page 117 and 118: 3. Replace the product manifold. Ma
Page 119 and 120: SP-519 Inogen One G3 LCD Cable Repl
Page 125 and 126: SP-520 Inogen One G3 Dual Feed Tube
Page 129 and 130: Feed tube and inlet union Figure 8:
Page 131 and 132:
Figure 13: Properly installed dual
Page 133 and 134:
Figure 16: Housing feet and corresp
Page 135 and 136:
Figure 2: Location of screws 3. Wit
Page 137 and 138:
Figure 6: Spring and spring nest as
Page 139 and 140:
SP-522 Inogen One G3 Column Recepta
Page 141 and 142:
Column latch Figure 4: Location of
Page 143 and 144:
7. Assure both lower grommets are i
Page 145 and 146:
SP-523 Inogen One G3 Chassis Replac
Page 147 and 148:
Figure 3: Chassis gasket 8. See “
Page 149 and 150:
Inogen One G3 Troubleshooting Guide
Page 151 and 152:
The battery icon on the LCD shows t
Page 153 and 154:
O2 Delivery Error No Error Message
show all

Inogen One G3 Technical Manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?