Inogen One G3 Technical Manual

More documents

Recommendations

Info

Cannula tube LCD cable Figure 8: Remove cannula tube and LCD cable Instructions for Removing the Motherboard: 1. Locate the compressor cable. Detach the compressor cable from the motherboard using long pliers to press down on the release clip while pulling the connector housing (Figure 9). Do not pull on the compressor wires. Compressor cable Figure 9: Detach compressor cable from motherboard 2. Unscrew the five screws that attach the motherboard to the chassis on the back side of the device (Figure 10). 96-03997-00-01 revA Service Manual, Inogen One G3 - 96 -
Figure 10: Screws to be removed from motherboard 3. Carefully pull the motherboard about a half inch away from the device, making sure not to bend it in any way. With the cables and tubing exposed, gently unplug the two feed waste manifold cables, the product manifold cable, and the fan cable from the motherboard (Figure 11). Product manifold cable Fan cable Feed waste cables Figure 11: Disconnect all cables that connect device to motherboard 4. Unplug the oxygen sensor tubing from the product manifold by pulling the tube off of the barb. Also unplug the accumulator tubing from the accumulator cap by pushing down on the retaining ring of the quick connect while pulling gently on the tubing (Figure 12). Pulling the tube too hard will result in breaking the pressure sensor free from the circuit board. 96-03997-00-01 revA Service Manual, Inogen One G3 - 97 -
Page 1 and 2:
INOGEN ONE G3 OXYGEN CONCENTRATOR S
Page 3 and 4:
SP-501 and SP-502 Inogen One G3 Fro
Page 5 and 6:
Figure 4: Location of screws 5. Sli
Page 7 and 8:
2. To remove the back housing, plac
Page 9 and 10:
Figure 6: Location of front screws
Page 11 and 12:
3. Re-install the two screws securi
Page 13 and 14:
Parts Required: 1. SP-504, LCD Tool
Page 15 and 16:
Page 17 and 18:
Cannula tube LCD cable Figure 8: Re
Page 19 and 20:
Figure 11: Housing feet and corresp
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Figure 10: Inlet T tube and inlet u
Page 27 and 28:
SP-506 Inogen One G3 Exhaust T Tube
Page 29 and 30:
Page 31 and 32:
Cannula tube LCD cable Figure 8: Re
Page 33 and 34:
Figure 11: Housing feet and corresp
Page 35 and 36:
Figure 2: Filter box lid screws 3.
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Figure 10: Location of rear filter
Page 43 and 44:
Compressor cable Exhaust tube Figur
Page 45 and 46: 5. Plug the other end of the dual f
Page 47 and 48: SP-509 Inogen One G3 Compressor Rep
Page 49 and 50: Figure 4: Filter box lid screws 3.
Page 51 and 52: Compressor cable Exhaust tube Figur
Page 53 and 54: SP-510 Inogen One G3 Power Cable Re
Page 55 and 56: Figure 4: Location of screws 5. Sli
Page 57 and 58: Cannula tube LCD cable Figure 8: Re
Page 59 and 60: Figure 11: Housing feet and corresp
Page 61 and 62: Figure 1: Direction to slide device
Page 63 and 64: Figure 5: Location of rear screws F
Page 65 and 66: Figure 9: Manifold bracket screw 2.
Page 67 and 68: Instructions for Replacing the Hous
Page 69 and 70: 2. To remove the back housing, plac
Page 71 and 72: Figure 6: Location of front screws
Page 73 and 74: Exhaust T tube Manifold screws Inta
Page 75 and 76: SP-513 Inogen One G3 Accumulator Re
Page 81 and 82: Figure 12: Properly installed accum
Page 83 and 84: SP-514 Inogen One G3 Breath Detect
Page 89 and 90: O2 sensor tubing Accumulator tubing
Page 93 and 94: Figure 1: Direction to slide device
Page 95: Figure 6: Location of front screws
Page 101 and 102: 2. To remove the back housing, plac
Page 103 and 104: Figure 6: Filter box lid screws 3.
Page 105 and 106: Instructions for Replacing the Hous
Page 109 and 110: Parts Required: 1. SP-518, Muffler
Page 111 and 112: Figure 3: Direction to slide housin
Page 113 and 114: Figure 7: Unplug UIP cable from mot
Page 115 and 116: Figure 11: Product manifold motherb
Page 117 and 118: 3. Replace the product manifold. Ma
Page 119 and 120: SP-519 Inogen One G3 LCD Cable Repl
Page 125 and 126: SP-520 Inogen One G3 Dual Feed Tube
Page 129 and 130: Feed tube and inlet union Figure 8:
Page 131 and 132: Figure 13: Properly installed dual
Page 135 and 136: Figure 2: Location of screws 3. Wit
Page 137 and 138: Figure 6: Spring and spring nest as
Page 139 and 140: SP-522 Inogen One G3 Column Recepta
Page 141 and 142: Column latch Figure 4: Location of
Page 143 and 144: 7. Assure both lower grommets are i
Page 145 and 146: SP-523 Inogen One G3 Chassis Replac
Page 147 and 148:
Figure 3: Chassis gasket 8. See “
Page 149 and 150:
Inogen One G3 Troubleshooting Guide
Page 151 and 152:
The battery icon on the LCD shows t
Page 153 and 154:
O2 Delivery Error No Error Message
show all

Inogen One G3 Technical Manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?