Online Edition for Part no. 01 41 2 604 027 - © 03/10 BMW AG
Online Edition for Part no. 01 41 2 604 027 - © 03/10 BMW AG
Online Edition for Part no. 01 41 2 604 027 - © 03/10 BMW AG
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
The corresponding memory button 1 is <strong>no</strong>w<br />
programmed with the signal of the original<br />
hand-held transmitter.<br />
You can operate the device when the engine is<br />
running or when the ignition is switched on.<br />
If the device can<strong>no</strong>t be used after<br />
repeated programming, check whether<br />
the original hand-held transmitter uses an alternating-code<br />
system. To do so, either read the<br />
instructions <strong>for</strong> the original hand-held transmitter<br />
or hold down the programmed memory<br />
button 1 of the integrated universal remote<br />
control. If the LED 2 on the integrated universal<br />
remote control flashes rapidly <strong>for</strong> a short time<br />
and then remains lit <strong>for</strong> approx. 2 seconds, this<br />
indicates that the original hand-held transmitter<br />
uses an alternating-code system. In the case of<br />
an alternating-code system, program the memory<br />
buttons 1 as described at Alternating-code<br />
hand-held transmitters.<<br />
Alternating-code hand-held<br />
transmitters<br />
To program the integrated universal remote<br />
control, consult the operating instructions <strong>for</strong><br />
the equipment to be set. You will find in<strong>for</strong>mation<br />
there on the possibilities <strong>for</strong> synchronization.<br />
When programming hand-held transmitters<br />
that employ an alternating code, observe the<br />
following supplementary instructions:<br />
Programming will be easier with the aid of<br />
a second person.<<br />
1. Park your vehicle within the range of the<br />
remote-controlled device.<br />
2. Program the integrated universal remote<br />
control as described above in the section<br />
Fixed-code hand-held transmitters.<br />
3. Locate the button on the receiver of the<br />
device to be set, e.g. on the drive unit.<br />
4. Press the button on the receiver of the<br />
device to be set. After step 4, you have<br />
approx. 30 seconds <strong>for</strong> step 5.<br />
5. Press the programmed memory button 1<br />
of the integrated universal remote control<br />
three times.<br />
The corresponding memory button 1 is <strong>no</strong>w<br />
programmed with the signal of the original<br />
hand-held transmitter.<br />
Should you have questions, please contact<br />
your <strong>BMW</strong> Sports Activity Vehicle<br />
Center.<<br />
Deleting all stored programs<br />
Press the left and right-hand memory button 1<br />
<strong>for</strong> approx. 20 seconds until the LED 2 flashes<br />
quickly:<br />
All stored programs are deleted.<br />
Reassigning individual programs<br />
1. Hold the original hand-held transmitter at a<br />
distance of approx. 4 in/<strong>10</strong> cm to 12 in/<br />
30 cm from the memory buttons 1.<br />
The required distance between the<br />
hand-held transmitter and the memory<br />
buttons 1 depends on the relevant system<br />
of the original hand-held transmitter<br />
used.<<br />
2. Press the desired memory button 1 of the<br />
integrated universal remote control.<br />
3. When the LED 2 flashes slowly after approx.<br />
20 seconds, press the transmit button of<br />
the original hand-held transmitter. Release<br />
both buttons as soon as the LED 2 flashes<br />
rapidly. If the LED 2 does <strong>no</strong>t flash rapidly<br />
after approx. 15 seconds, alter the distance<br />
and repeat the step.<br />
Digital compass*<br />
1 Adjustment button<br />
2 Display<br />
125<br />
Reference Mobility<br />
Communications Entertainment Navigation Driving tips Controls<br />
At a glance