Super Smart Ball Bushing Bearing - Hollin Applications

Phone: 1-800-554-8466Website: www.thomsonballbushing.comFluoroNyliner*FluoroNyliner* Bushing Bearing Pillow BlocksCLOSED PILLOW BLOCKS WITH SELF-ALIGNING BEARINGSA2SINGLE PILLOW BLOCKG1TWIN PILLOW BLOCKG1H1HFGF1NNE1EEABBEND VIEW SIDE VIEW SIDE VIEWGCLOSED SINGLE PILLOW BLOCKS WITH SELF-ALIGNING BEARINGSPrecision I.D. Compensated I.D. I.D. (1) (1) Twin Open Pillow Bearing Block Dimensions (in.) (in.)Part Number Part Number H H1 A A2 B E E1 F F1 G G1 N Pillow Max±0.003 ±0.010 ±0.010Hole / BoltBlockMass (lb)StaticLoad (lbf)FNYBU-PB-04-A-LS FNYBU-PB-04-AL-LS .437 .81 1.63 1.00 1.19 .750 1.313 .75 .19 .44 .22 .16 #6 .10 300FNYBU-PB-06-A-LS FNYBU-PB-06-AL-LS .500 .94 1.75 1.13 1.31 .875 1.438 .88 .19 .50 .22 .16 #6 .13 500FNYBU-PB-08-A-LS FNYBU-PB-08-AL-LS .687 1.25 2.00 1.38 1.69 1.000 1.688 1.13 .25 .59 .84 .16 #6 .40 970FNYBU-PB-10-A-LS FNYBU-PB-10-AL-LS .875 1.63 2.50 1.75 1.94 1.125 2.125 1.44 .28 .85 .68 .19 #8 1.00 1450FNYBU-PB-12-A-LS FNYBU-PB-12-AL-LS .937 1.75 2.75 1.88 2.06 1.250 2.375 1.56 .31 .94 .72 .19 #8 1.20 1900FNYBU-PB-16-A-LS FNYBU-PB-16-AL-LS 1.187 2.19 3.25 2.38 2.81 1.750 2.875 1.94 .38 1.19 .86 .22 #10 2.40 3500FNYBU-PB-20-A-LS FNYBU-PB-20-AL-LS 1.500 2.81 4.00 3.00 3.63 2.000 3.500 2.50 .44 1.50 1.20 .22 #10 5.00 5100FNYBU-PB-24-A-LS FNYBU-PB-24-AL-LS 1.750 3.25 4.75 3.50 4.00 6.500 2.500 2.88 .50 1.75 1.25 .28 1/4 7.80 7000FNYBU-PB-24-A-LS FNYBU-PB-24-AL-LS 2.125 4.06 6.00 4.50 5.00 3.250 3.250 3.63 .63 2.12 1.58 .41 1/4 7.80 12,500CLOSED TWIN BEARING PILLOW BLOCKS WITH SELF-ALIGNING BEARINGSPrecision I.D. Compensated I.D. I.D. (1) (1) Twin Open Pillow Bearing Block Dimensions (in.) (in.)Part Number Part Number H H1 A A2 B E E1 F F1 G G1 N Pillow Max±0.003 ±0.010 ±0.010Hole / BoltBlockMass (lb)StaticLoad (lbf)FNYBU-TWN-04-A-LS FNYBU-TWN-04-AL-LS .437 .81 1.63 1.00 2.50 2.000 1.313 .75 .19 .44 1.25 .16 #6 .19 600FNYBU-TWN-06-A-LS FNYBU-TWN-06-AL-LS .500 .94 1.75 1.13 2.75 2.050 1.438 .88 .19 .50 1.37 .16 #6 .25 1000FNYBU-TWN-08-A-LS FNYBU-TWN-08-AL-LS .687 1.25 2.00 1.38 3.50 2.000 1.688 1.13 .25 .59 1.75 .16 #6 .40 1940FNYBU-TWN-10-A-LS FNYBU-TWN-10-AL-LS .875 1.63 2.50 1.75 4.00 3.000 2.125 1.44 .28 .85 2.00 .19 #8 1.00 2900FNYBU-TWN-12-A-LS FNYBU-TWN-12-AL-LS .937 1.75 2.75 1.88 4.50 3.500 2.375 1.56 .31 .94 2.25 .19 #8 1.20 3800FNYBU-TWN-16-A-LS FNYBU-TWN-16-AL-LS 1.187 2.19 3.25 2.38 6.00 4.500 2.875 1.94 .38 1.19 3.00 .22 #10 2.40 7000FNYBU-TWN-20-A-LS FNYBU-TWN-20-AL-LS 1.500 2.81 4.00 3.00 7.50 5.500 3.500 2.50 .44 1.50 3.75 .22 #10 5.00 10,200FNYBU-TWN-24-A-LS FNYBU-TWN-24-AL-LS 1.750 3.25 4.75 3.50 9.00 6.500 4.125 2.88 .50 1.75 4.50 .28 1/4 7.80 14,000(1) Compensated I.D. bearings have additional running clearance, ideally suited for high speed and non-parallel shaft applications.(2) All dimensions in inches unless otherwise noted.Note: For Pillow Block Seals or non-self-aligning bearings see Part Number Matrix on Page 123.©2003 Danaher Motion. Printed in the U.S.A. The specifications in this publication are believed to be accurate and reliable.However, it is the responsibility of the product user to determine the suitability of Thomson products for a specific application.While defective products will be replaced without charge if promptly returned, no liability is assumed beyond such replacement.Page 121* Trademark of Danaher Motion. DANAHER MOTION is registered in the U.S. Patent and Trademark Office and in other countries.