Super Smart Ball Bushing Bearing - Hollin Applications

Phone: 1-800-554-8466Website: www.thomsonballbushing.comSuper Smart Ball Bushing Bearings60 Case LinearRace Shaft Support Blocksfor End Supported ApplicationsType SB LinearRace Shaft Support BlockA2H1HN3dType SB 60 Case* LinearRace* Shaft End Support Blocks (Dimensions in inches)Nom. H H1 H2 A A2 B E N3LinearRacePart (2) Dia.MassNo. d ±.002±.010 Hole Bolt lbSB-8 .500 1.00 1.63 .25 2.00 .75 .63 1.500 .19 #8 .3SB-12 .750 1.250 2.13 .31 2.75 1.00 .75 2.000 .22 #10 .5SB-16 1.000 1.500 2.56 .38 3.25 1.38 1.00 2.500 .28 .25 1.0SSUEAMaterial: Malleable IronH2BType ASB LinearRace Shaft Support BlockH1HEAMaterial: Aluminum AlloyA1N3BdType ASB 60 Case LinearRace Shaft End Support BlocksH H1 A A1 BNom.LinearRaceDia.d(Dimensions in inches)E N3Part (2)MassNo.±.001±.001Hole Bolt lbASB-8 .500 .875 1.48 2.00 1.000 .63 1.50 .19 #8 .11ASB-12 .750 1.125 1.95 2.50 1.250 .75 2.00 .22 #10 .22ASB-16 1.000 1.375 2.48 3.25 1.625 1.00 2.50 .28 .25 .44Type FSB Flanged LinearRace Support BlockBBACA C FGMaterial: Aluminum AlloyDEJType FSB Flanged 60 Case LinearRace Shaft End Support BlocksA B C D E FPart (2)No.Nom.LinearRaceDia.dFSB-8 .500 1.63 .81 1.250 .88FSB-12 .750 2.38 1.19 1.750 1.00FSB-16 1.000 2.75 1.38 2.125 1.25FSB-20 1.250 3.13 1.56 2.375 1.38(1)The Dynamic Load Capacity is based on a rated travel life of 2 million inches. The actual Dynamic Load Capacity can be affected by theorientation of the bearing or the direction of the applied load. For dynamic load correction factors see polar graphs below. Dynamic loadcapacity of Twin Super Smart Flanged Pillow blocks is based on two bearings equally loaded.(2)For part number description and specifications see page 14 & 15.Note: For additional technical data, see the Engineering Support Appendix.±.010.50.63.63.751.001.251.501.75(Dimensions in inches)G JHole.18.21.27.27Bolt#8#101⁄41 ⁄4.25.31.31.38Masslb.3.6.8.9Polar GraphsThe actual Dynamic Load Capacity of a BallBushing* bearing is determined by the orientationof the bearing or direction of the applied load.The load Correction Factor K 0 is found by knowingthe direction of the applied load relative to theorientation of the bearings ball tracks and referringto the polar graph. To determine the actualDynamic Load Capacity, multiply the propercorrection factor by the Dynamic Load Capacitylisted in the product table on the previous page.SSUFB-12SSUFB-16SSUFB-20SSUFB-24SSUTFB-12SSUTFB-16SSUTFB-20SSUTFB-24K O1800SS6UFB-8SS6UTFB-8900,60,70,80,91,0270K O©2003 Danaher Motion. Printed in the U.S.A. The specifications in this publication are believed to be accurate and reliable.However, it is the responsibility of the product user to determine the suitability of Thomson products for a specific application.While defective products will be replaced without charge if promptly returned, no liability is assumed beyond such replacement.Page 23* Trademark of Danaher Motion. DANAHER MOTION is registered in the U.S. Patent and Trademark Office and in other countries.