Super Smart Ball Bushing Bearing - Hollin Applications

Phone: 1-800-554-8466Website: www.thomsonballbushing.com60 Case LinearRace Support Blocksfor End Supported ApplicationsPrecision Steel Ball Bushing BearingH1Type SB LinearRace Support BlockHA2EAMaterial: Malleable IronN3H2BdType SB 60 Case* LinearRace* End Support BlocksH H1 H2 A A2Part (2)No.NominalLinearRaceDiameterd±.002(Dimensions in inches)E N N3SB-8 .500 1.000 1.63 .25 2.00 .75 .63 1.500 .19 #8 .3SB-12 .750 1.250 2.13 .31 2.75 1.00 .75 2.000 .22 #10 .5SB-16 1.000 1.500 2.56 .38 3.25 1.38 1.00 2.500 .28 .25 1.0SB-20 1.250 1.750 3.00 .44 4.00 1.75 1.13 3.000 .34 .31 2.0SB-24 1.500 2.000 3.50 .50 4.75 2.00 1.25 3.500 .34 .31 2.6SB-32 2.000 2.500 4.50 .63 6.00 2.63 1.50 4.500 .41 .38 4.8B±.010HoleBoltWt.lbType ASB LinearRace Support BlockH1HEAMaterial: Aluminum AlloyA1N3BdType ASB 60 Case LinearRace End Support BlocksNominal H H1 A A1 BLinearRacePart (2) DiameterNo. d ±.001±.001ASB-8 .500 .875 1.48 2.00 1.000 .63ASB-12 .750 1.125 1.95 2.50 1.250 .75ASB-16 1.000 1.375 2.48 3.25 1.625 1.00ASB-24 1.500 2.000 3.50 4.75 2.375 1.25(Dimensions in inches)E N N3Wt.Hole Bolt lb1.50 .19 #8 .112.00 .22 #10 .222.50 .28 .25 .443.50 .34 .31 1.16Type FSB Flanged LinearRace Support BlockADCEBGJA C FBMaterial: Aluminum AlloyType FSB Flanged 60 Case LinearRace End Support BlocksA B C D E FPartNo.NominalLinearRaceDiameterd.500.7501.0001.250±.010FSB-8 1.63 .81 1.250 .88FSB-12 2.38 1.19 1.750 1.00FSB-16 2.75 1.38 2.125 1.25FSB-20 3.13 1.56 2.375 1.38.50.63.63.751.001.251.501.75(Dimensions in inches)G JMassHole Boltlb.18 #8 .25 .3.21 #10 .31 .6.27.271 ⁄4⁄4.31.38.8.9(1)The Dynamic Load Capacity is based on a rated travel life of 2 million inches. The actual Dynamic Load Capacity can be affected by the orientation of the bearingor the direction of the applied load. For dynamic load correction factors see polar graphs below.(2)For part number description and specifications see page 72 and 73.Note: Precision Steel Ball Bushing bearings are available in corrosion resistant stainless steel in diameters up to 1 inch. Dynamic load ratings are reduced by 30%when using stainless steel Ball Bushing bearings. See Engineering Support Appendix page 136. For additional technical data, see Engineering Support Appendix.Polar GraphsThe actual Dynamic Load Capacity of a Ball Bushing bearing is determined by the orientation of the bearing or direction of the applied load. The load CorrectionFactor K 0 is found by knowing the direction of the applied load relative to the orientation of the bearings ball tracks and referring to the polar graph. To determinethe actual Dynamic Load Capacity, multiply the proper correction factor by the Dynamic Load Capacity listed in the product table on the previous page.K 0K 0 K 0PB-8-APB-8-ADJPB-12-APB-12-ADJPB-16-APB-16-ADJPB-20-APB-20-ADJPB-24-APB-24-ADJPB-32-APB-32-ADJ©2003 Danaher Motion. Printed in the U.S.A. The specifications in this publication are believed to be accurate and reliable.However, it is the responsibility of the product user to determine the suitability of Thomson products for a specific application.While defective products will be replaced without charge if promptly returned, no liability is assumed beyond such replacement.Page 81* Trademark of Danaher Motion. DANAHER MOTION is registered in the U.S. Patent and Trademark Office and in other countries.