Super Smart Ball Bushing Bearing - Hollin Applications

Phone: 1-800-554-8466Website: www.thomsonballbushing.comRetaining RingsAInternal Retaining Rings(Type PR)Push-in retaining rings, as shown, are for usewith Super Smart, Super and Precision SteelBall Bushing* closed type bearings. Eachretaining ring is installed inside the housingbore at each end of the Ball Bushing bearing.BInternal Retaining Rings (Type PR)Use withBall Bushing BearingPart NumberPart NumberSUPER-4 or 4812 (1)SUPER-6 or 61014 (1)SUPER-8 or 81420 (1)SSU-10 or SUPER-10 or 101824 (1)SSU-12 or SUPER-12 or 122026 (1)SSU-16 or SUPER-16 or 162536 (1)SSU-20 or SUPER-20 or 203242 (1)SSU-24 or SUPER-24 or 243848 (1)SUPER-32 or 324864 (1)AccessoriesNominalHousing BoreA(Dimensions in inches)Minimum EndSpace RequiredBPR-250 .500 .060PR-375 .625 .060PR-500 .875 .080PR-625 1.125 .080PR-750 1.250 .080PR-1000 1.563 .080PR-1250 2.000 .080PR-1500 2.375 .100PR-2000 3.000 .100(1)Applies to A and XA Type Precision Steel Ball Bushing bearingsO.D.External Retaining Rings(Type W)External retaining rings fit into the retainingring grooves on the outside diameter of SuperSmart, Super and Precision Steel Ball Bushingbearings to provide external mounting retention.Available in standard and stainless steelversions.External Retaining Rings(Type C)External retaining rings fit into the retainingring grooves on the outside diameter of SuperSmart, Super and Precision Steel Ball Bushingbearings (Open and Closed Type) to provideexternal mounting retention. Available instandard and stainless steel versions.TTO.D.External Retaining Rings (Types C and W)Standard SteelPart NumberStainless SteelPart NumberUse withBall Bushing BearingPart Number(Dimensions in inches)– W-125-SS INST-258-SS (2).025 .520– W-187-SS INST-369-SS (2).025 .560W-250 W-250-SS.035.720SUPER-4 or 4812 (2)C-250 C-250-SS.035.550W-375 W-375-SS.035.850SUPER-6 or 61014 (2)C-375 C-375-SS.035.673W-500 W-500-SS.0421.150SUPER-8 or 81420 (2)C-500 C-500-SS.042.923W-625 W-625-SS SSU-10 or SUPER-10 .0501.510C-625 C-625-SS or 101824 (2).050 1.180W-750 W-750-SS SSU-12 or SUPER-12 .0501.620C-750 C-750-SS or 122026 (2).050 1.301W-1000 W-1000-SS SSU-16 or SUPER-16 .0622.040C-1000 C-1000-SS or 162536 (2).062 1.620W-1250 – SSU-20 or SUPER-20 .062 2.500C-1250 – or 203242 (2).062 2.040W-1500 – SSU-24 or SUPER-24 .078 2.910C-1500 – or 243848 (2).078 2.429W-2000– SUPER-32 or 324864 (2) .0933.600W-2500– 406080 (2).1094.420W-3000 – 487296 (2).1095.310W-4000 – 6496128 (2).1257.100(2)Applies to A, XA and OPN Type Precision Steel Ball Bushing bearingsTO.D.©2003 Danaher Motion. Printed in the U.S.A. The specifications in this publication are believed to be accurate and reliable.However, it is the responsibility of the product user to determine the suitability of Thomson products for a specific application.While defective products will be replaced without charge if promptly returned, no liability is assumed beyond such replacement.Page 127* Trademark of Danaher Motion. DANAHER MOTION is registered in the U.S. Patent and Trademark Office and in other countries.