Super Smart Ball Bushing Bearing - Hollin Applications

FluoroNyliner*Phone: 1-800-554-8466Website: www.thomsonballbushing.comFluoroNyliner* Bushing Bearing Pillow BlocksOPEN PILLOW BLOCKS WITH SELF-ALIGNING BEARINGSSINGLE PILLOW BLOCKTWIN PILLOW BLOCKH1HAE1F1GBENGBENE230A2G1G1END VIEW 30SIDE VIEW SIDE VIEWOPEN SINGLE PILLOW BLOCKS WITH SELF-ALIGNING BEARINGSPrecision I.D. Compensated I.D. I.D. (1) (1) Single Open Pillow Bearing Block Dimensions (in.) (in.)Part Number Part Number H H1 A A2 B E E1 F1 G G1 N Pillow Max±0.003 ±0.010 ±0.010Hole / BoltBlockMass (lb)StaticLoad (3) (lbf)FNYBU-PBO-08-A-LS FNYBU-PBO-08-AL-LS .687 1.25 2.00 1.38 1.69 1.000 1.688 .25 .69 .84 .16 #6 .20 970FNYBU-PBO-10-A-LS FNYBU-PBO-10-AL-LS .875 1.63 2.50 1.75 1.94 1.125 2.125 .28 .70 .68 .19 #8 .50 1450FNYBU-PBO-12-A-LS FNYBU-PBO-12-AL-LS .937 1.75 2.75 1.88 2.06 1.250 2.375 .31 .94 .72 .19 #8 .60 1900FNYBU-PBO-16-A-LS FNYBU-PBO-16-AL-LS 1.187 2.19 3.25 2.38 2.81 1.750 2.875 .38 1.20 .86 .22 #10 1.20 3500FNYBU-PBO-20-A-LS FNYBU-PBO-20-AL-LS 1.500 2.81 4.00 3.00 3.63 2.000 3.500 .44 1.50 1.20 .22 #10 2.50 5100FNYBU-PBO-24-A-LS FNYBU-PBO-24-AL-LS 1.750 3.25 4.75 3.50 4.00 2.500 4.125 .50 1.75 1.25 .28 1/4 3.80 7000FNYBU-PBO-32-A-LS FNYBU-PBO-32-AL-LS 2.125 4.06 6.00 4.50 5.00 3.250 5.250 .63 2.12 1.58 .41 3/8 7.00 12,500OPEN TWIN PILLOW BLOCKS WITH SELF-ALIGNING BEARINGSPrecision I.D. Compensated I.D. I.D. (1) (1) Twin Open Pillow Bearing Block Dimensions (in.) (in.)Part Number Part Number H H1 A A2 B E E1 F1 G G1 N Pillow Max±0.003 ±0.010 ±0.010Hole / BoltBlockMass (lb)StaticLoad (3) (lbf)FNYBU-TWNO-08-A-LS FNYBU-TWNO-08-AL-LS .687 1.25 2.00 1.38 3.50 2.000 1.688 .25 .59 1.75 .16 #6 .40 1940FNYBU-TWNO-10-A-LS FNYBU-TWNO-10-AL-LS .875 1.63 2.50 1.75 4.00 3.000 2.125 .28 .85 2.00 .19 #8 1.00 2900FNYBU-TWNO-12-A-LS FNYBU-TWNO-12-AL-LS .937 1.75 2.75 1.88 4.50 3.500 2.375 .31 .94 2.25 .19 #8 1.20 3800FNYBU-TWNO-16-A-LS FNYBU-TWNO-16-AL-LS 1.187 2.19 3.25 2.38 6.00 4.500 2.875 .38 1.20 3.00 .22 #10 2.40 7000FNYBU-TWNO-20-A-LS FNYBU-TWNO-20-AL-LS 1.500 2.81 4.00 3.00 7.50 5.500 3.500 .44 1.50 3.75 .22 #10 5.00 10,200FNYBU-TWNO-24-A-LS FNYBU-TWNO-24-AL-LS 1.750 3.25 4.75 3.50 9.00 6.500 4.125 .50 1.75 4.50 .28 1/4 7.80 14,000(1) Compensated I.D. bearings have additional running clearance, ideally suited for high speed and non-parallel shaft applications.(2) All dimensions in inches unless otherwise noted.(3) Open bearings operating in shear should be derated by 40%. Open bearings operating in tension should be derated by 70%.Note: For Pillow Block Seals or non-self-aligning bearings see Part Number Matrix on Page123.Page 122©2003 Danaher Motion. Printed in the U.S.A. The specifications in this publication are believed to be accurate and reliable.However, it is the responsibility of the product user to determine the suitability of Thomson products for a specific application.While defective products will be replaced without charge if promptly returned, no liability is assumed beyond such replacement.* Trademark of Danaher Motion. DANAHER MOTION is registered in the U.S. Patent and Trademark Office and in other countries.