Super Smart Ball Bushing Bearing - Hollin Applications

Phone: 1-800-554-8466Website: www.thomsonballbushing.com60 Case LinearRace Support Blocksfor End Supported ApplicationsH1HA2EAN3H2Material: Malleable Iron for sizes .5 to 2 in.Aluminum Alloy for sizes .25 and .375 in.H1HType SB LinearRace Support BlockType ASB LinearRace Support BlockEAMaterial: Aluminum AlloyBBACA1N3Type FSB Flanged LinearRace Support BlockA C FGMaterial: Aluminum AlloyBBDEJddPart (2)No.Super Ball Bushing BearingType SB 60 Case* LinearRace* End Support BlocksNominal H H1 H2 A A2 B ELinearRacePart (2) DiameterNo. d ±.002±.010SB-4 .250 .687 1.061.50 .63 .50 1.125SB-6 .375 .750 1.19 .25 1.63 .69 .56 1.250SB-8 .500 1.000 1.63 2.00 .75 .63 1.500(Dimensions in inches)N3MassHole Bolt lb.25 .16 #6 .03.16 #6 .05.25 .19 #8 .30SB-10SB-12.625.7501.0001.2501.752.13.31.312.502.75.881.00.69.751.8752.000.22.22#10#10.40.50SB-16 1.000 1.500 2.56 .38 3.25 1.38 1.00 2.500 .281 ⁄4 1.00SB-20 1.250 1.750 3.00 .44 4.00 1.75 1.13 3.000 .345 ⁄16 2.00SB-24 1.500 2.000 3.50 .50 4.75 2.00 1.25 3.500 .345 ⁄16 2.60SB-32 2.000 2.500 4.50 .63 6.00 2.63 1.50 4.500 .41 3 ⁄8 4.80Type ASB 60 Case LinearRace End Support BlocksNominal H H1 A A1 BLinearRacePart (2) DiameterNo. d ±.001±.001ASB-4 .250 .500 .88 1.50 .750 .50ASB-6 .375 .562 1.00 1.62 .813 .56ASB-8 .500 .875 1.48 2.00 1.000 .63ASB-12 .750 1.125 1.95 2.50 1.250 .75ASB-16 1.000 1.375 2.48 3.25 1.625 1.00ASB-24 1.500 2.000 3.50 4.75 2.375 1.25Type FSB Flanged 60 Case LinearRace End Support BlocksNominalLinearRaceDiameterd.500.7501.0001.250±.010FSB-8 1.63 .81 1.250 .88FSB-12 2.38 1.19 1.750 1.00FSB-16 2.75 1.38 2.125 1.25FSB-20 3.13 1.56 2.375 1.38(Dimensions in inches)E N3MassHole Bolt lb1.12 .16 #6 .061.25 .16 #6 .081.50 .19 #8 .112.00 .22 #10 .222.50 .281 ⁄4 .443.50 .345 ⁄16 1.16(Dimensions in inches)G J(1)The Dynamic Load Capacity is based on a rated travel life of 2 million inches. The actual Dynamic Load Capacity can be affected by theorientation of the bearing or the direction of the applied load. For dynamic load correction factors see polar graphs below.(2)For part number description and specifications see page 42 and 43.Note: For additional technical data, see Engineering Support Appendix.Polar GraphsThe actual Dynamic Load Capacity of a Ball Bushing bearing is determined by the orientation of the bearing or direction of the applied load. The load CorrectionFactor K 0 is found by knowing the direction of the applied load relative to the orientation of the bearings ball tracks and referring to the polar graph. To determinethe actual Dynamic Load Capacity, multiply the proper correction factor by the Dynamic Load Capacity listed in the product table on the previous page.ABCDE.50.63.63.75F1.001.251.501.75MassHole Boltlb.18 #8 .25 .3.21 #10 .31 .6.27.271 ⁄4⁄4.31.38.8.9SUPERK 0K 0K 0SPB-4 (-ADJ)SPB-6 (-ADJ)SPB-8 (-ADJ)SPB-10 (-ADJ)SPB-12 (-ADJ)SPB-16 (-ADJ)SPB-20 (-ADJ)SPB-24 (-ADJ)SPB-32 (-ADJ)©2003 Danaher Motion. Printed in the U.S.A. The specifications in this publication are believed to be accurate and reliable.However, it is the responsibility of the product user to determine the suitability of Thomson products for a specific application.While defective products will be replaced without charge if promptly returned, no liability is assumed beyond such replacement.Page 51* Trademark of Danaher Motion. DANAHER MOTION is registered in the U.S. Patent and Trademark Office and in other countries.