Super Smart Ball Bushing Bearing - Hollin Applications

Phone: 1-800-554-8466Website: www.thomsonballbushing.com60 Case LinearRace Support Blocksfor End Supported ApplicationsH1HType SB LinearRace Support BlockA2EAN3H2Material: Malleable Iron for sizes .5 to 2 in.Aluminum Alloy for sizes .25 and .375 in.BdSuper Ball Bushing BearingType SB 60 Case* LinearRace* End Support BlocksNominal H H1 H2 A A2 B ELinearRacePart (2) DiameterNo. d ±.002±.010SB-8 .500 1.000 1.63 2.00 .75 .63 1.500(Dimensions in inches)N3MassHole Bolt lb.25 .19 #8 .3SB-10SB-12.625.7501.0001.2501.752.13.31.312.502.75.881.00.69.751.8752.000.22.22#10#10.4.5SB-16 1.000 1.500 2.56 .38 3.25 1.38 1.00 2.500 .281 ⁄4 1.0H1HType ASB LinearRace Support BlockEAMaterial: Aluminum AlloyA1N3BdType ASB 60 Case LinearRace End Support BlocksH H1 A A1Part (2)No.NominalLinearRaceDiameterd.500.7501.000±.001±.001ASB-8 .875 1.48 2.00 1.000ASB-12 1.125 1.95 2.50 1.250ASB-16 1.375 2.48 3.25 1.625B.63.751.00E1.502.002.50(Dimensions in inches)N3Hole.19.22.28MassBolt lb#8 .11#10 .221 ⁄4 .44SUPERType FSB Flanged LinearRace Support BlockADCEBGJA C FBType FSB Flanged 60 Case LinearRace End Support BlocksA B C D E FPart (2)No.NominalLinearRaceDiameterd.500.7501.000±.010FSB-8 1.63 .81 1.250 .88FSB-12 2.38 1.19 1.750 1.00FSB-16 2.75 1.38 2.125 1.25.50.63.631.001.251.50(Dimensions in inches)G JMassHole Boltlb.18 #8 .25 .3.21 #10 .31 .6.27 1 ⁄4 .31 .8Material: Aluminum Alloy(1)The Dynamic Load Capacity is based on a rated travel life of 2 million inches. The actual Dynamic Load Capacity can be affected by theorientation of the bearing or the direction of the applied load. For dynamic load correction factors see polar graphs below.(2)For part number description and specifications see page 42 and 43.Note: For additional technical data, see Engineering Support Appendix.Polar GraphsThe actual Dynamic Load Capacity of a Ball Bushing bearing is determined by the orientation of the bearing or direction of the applied load. The load CorrectionFactor K 0 is found by knowing the direction of the applied load relative to the orientation of the bearings ball tracks and referring to the polar graph. To determinethe actual Dynamic Load Capacity, multiply the proper correction factor by the Dynamic Load Capacity listed in the product table on the previous page.K 0K 0K 0SUPER 8-DD SUPER 10-DD SUPER 12-DDSUPER 16-DD©2003 Danaher Motion. Printed in the U.S.A. The specifications in this publication are believed to be accurate and reliable.However, it is the responsibility of the product user to determine the suitability of Thomson products for a specific application.While defective products will be replaced without charge if promptly returned, no liability is assumed beyond such replacement.Page 47* Trademark of Danaher Motion. DANAHER MOTION is registered in the U.S. Patent and Trademark Office and in other countries.