NLS-HR100 Series Hand-held 1D Barcode Scanner User ... - Sensis

More documents

Recommendations

Info

SymbolsCode 11ToolsCode Programming ONSelect Message LengthIt is used to program the valid reading length of Code 11. The engine willsend an error beep, if the decoded data length does not match the validlength.Code 11 Message Length is defined by “Min. Message Length” and“Max. Message Length ”.Code Programming OFFMin Message Length【Pro CMD:99912713】Max Message Length【Pro CMD:99912714】<strong>1D</strong> bar code Message Length should not exceed 255 bytes. If Max Message Length is lessthan Min Message Length, it means the engine will only support barcodes of the two lengths.If Max Message Length is equal to Min Message Length, the engine will only support barcodesof the length.To set Min Message Length of Code 11 to 8 bytes and the Max Message Length to 12bytes. Read these programming code:1. “Code Programming ON”2. “Select Min Message Length”3. Digit Code “8”, see Digit Code (Appendix Pxxx)4. “Save Programming”, see Digit Code (Appendix Pxxx)5. “Select Max Message Length”6. Digit Code “1”7. Digit Code “2”8. “Save Programming”9. “Code Programming OFF”nlscan.comPage 106
SymbolsPlesseyToolsCode Programming ONLoad Factory DefaultCode Programming OFFLoad Plessey Factory Default【Pro CMD:99913000】Enable/ Disable PlesseyEnable Plessey【Pro CMD:99913002】Disable Plessey【Pro CMD:99913001】When the engine can not read Plessey, please read “Enable Plessey” and try again.Plessey Code IDCode ID Setting【Pro CMD:99913010】Example of setting Plessey Code ID to “p” (0x70)1. Read Enable Code Programming barcode.2. Read Plessey Code ID Setting barcode.3. Read Following <strong>Barcode</strong>s: “7”, and “0”4. Read Save barcode5. Read Disable Code Programming barcode.nlscan.comPage 107
Page 5:
Table of ContentsSecurity Level ...
Page 8 and 9:
Table of ContentsCode 39 Code ID ..
Page 10 and 11:
About this guideGraphic NotationsTo
Page 12 and 13:
Getting to StartUnpackingUnpackingU
Page 14 and 15:
Getting to StartCommunication Ports
Page 16 and 17:
Getting to StartConnecting with RS2
Page 18 and 19:
Getting to StartRemoval of Communic
Page 20:
Getting to StartReading1、Ensure H
Page 24:
General ProgrammingIntroductionTher
Page 27:
General ProgrammingCommand Programm
Page 30 and 31:
General ProgrammingWorking ModeTool
Page 32 and 33:
General ProgrammingReading ModeAuto
Page 34 and 35:
General ProgrammingReading ModeSens
Page 36 and 37:
General ProgrammingReading ModeDela
Page 38 and 39:
General ProgrammingSecurity LevelTh
Page 40 and 41:
General ProgrammingOthersStart/Stop
Page 42 and 43:
Communication ProgrammingIntroducti
Page 44 and 45:
Communication ProgrammingSerial Por
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
Communication ProgrammingKeyboard P
Page 52 and 53:
Data FormatIntroduction1D barcodes
Page 54 and 55:
Data FormatUser PrefixToolsCode Pro
Page 56 and 57:
Data FormatCode ID PrefixBesides AI
Page 58 and 59:
Data FormatTerminalToolsCode Progra
Page 60 and 61:
SymbolsCode 128Load Factory Default
Page 64 and 65: SymbolsAIM 128ToolsCode Programming
Page 66 and 67: SymbolsEAN-8ToolsCode Programming O
Page 68 and 69: SymbolsEAN-8ToolsCode Programming O
Page 70 and 71: SymbolsEAN-13Check DigitToolsCode P
Page 72 and 73: SymbolsISSNToolsCode Programming ON
Page 74 and 75: SymbolsISBNToolsCode Programming ON
Page 76 and 77: SymbolsUPC-ECheck DigitToolsCode Pr
Page 78 and 79: SymbolsUPC-ETransmit Default “0
Page 80: SymbolsUPC-ACheck DigitToolsCode Pr
Page 83 and 84: SymbolsInterleaved 2 of 5Check Digi
Page 85 and 86: SymbolsITF-6ITF-6 is a fixed length
Page 87 and 88: SymbolsDeutshe14Load Factory Defaul
Page 89 and 90: SymbolsCOOP25(Japanese Matrix 2 of
Page 91 and 92: SymbolsCOOP25(Japanese Matrix 2 of
Page 93 and 94: SymbolsMatrix 2 of 5( European Matr
Page 95 and 96: SymbolsIndustrial 25ToolsCode Progr
Page 97 and 98: SymbolsIndustrial 25ToolsCode Progr
Page 99 and 100: SymbolsStandard 25Check DigitToolsC
Page 101 and 102: SymbolsCode 39ToolsCode Programming
Page 103 and 104: SymbolsCode 39Transmit Start & Stop
Page 105 and 106: SymbolsCodabarToolsCode Programming
Page 107 and 108: SymbolsCodabarTransmit Start & Stop
Page 109 and 110: SymbolsCode 93ToolsCode Programming
Page 111 and 112: SymbolsCode 93Select Message Length
Page 113: SymbolsCode 11Check DigitCode 11 ma
Page 117 and 118: SymbolsPlesseyToolsCode Programming
Page 119 and 120: SymbolsMSI-PlesseyCheck DigitMSI-Pl
Page 121 and 122: SymbolsGS1 DatabarToolsCode Program
Page 123 and 124: AppendixFactory Default ListSymbolC
Page 125 and 126: AppendixFactory Default ListDeutsch
Page 127 and 128: AppendixFactory Default ListSend Ch
Page 129 and 130: AppendixCode ID ListSymbolCode 128U
Page 131 and 132: AppendixDigit CodeToolsCode Program
Page 133 and 134: AppendixASCII TableHex Dec Char00 0
Page 135 and 136: AppendixASCII TableHex Dec Char59 8
show all

NLS-HR100 Series Hand-held 1D Barcode Scanner User ... - Sensis

Create successful ePaper yourself

Delete template?

Save as template?