NLS-HR100 Series Hand-held 1D Barcode Scanner User ... - Sensis

More documents

Recommendations

Info

Getting to StartRemoval of Communication CableA Pin that fit the HR100 Series “Dismount hole” is needed. A paper clip could be ideal. Stretch one end ofthe paper clip to fit the “Dismount Hole”. Follow the steps:1、For RS232 and PS/2 connections, unplug the power adaptor.2、Insert the Pin into “Dismount Hole” and keep some pressure.3、Pull out the cable gently.4、Pull out the Pin after the cable is removed.5、Unplug the connector from the Host.nlscan.comPage 10
Getting to StartON, OFF, IDLE, RESTARTPower OnConnect HR100 Series and Host. One click the "Trigger". HR100 Series powers on and in "Idle" (readyto use) state (factory default).Power OffThere are 4 ways to "Power OFF":» Remove Cable Off HR100 Series;»»»Remove Power Adapter Off RS232 Cable;Remove USB Cable Off the Host;Remove PS/2 cable off the Host and power adaptor.IDLEWhen reader is NOT reading, it is in "IDLE mode".No reading attempt within a timeout, the Imager switch to IDLE mode automatically.RESTARTIf HR100 Series halted and does not respond to operations, please "Restart" by "Power OFF", and then"Power ON".Maintenance»»»»»»The scan window must be kept clean. Improper maintenance will breach the limited warranty.Avoid rough objects not to damage or scratch the window.Use brush to remove the stain.Use soft cloth (cloth for glasses) to clean.Prohibit spraying towards the window.Only use clean water as a cleanser.nlscan.comPage 11
Page 5: Table of ContentsSecurity Level ...
Page 8 and 9: Table of ContentsCode 39 Code ID ..
Page 10 and 11: About this guideGraphic NotationsTo
Page 12 and 13: Getting to StartUnpackingUnpackingU
Page 14 and 15: Getting to StartCommunication Ports
Page 16 and 17: Getting to StartConnecting with RS2
Page 20: Getting to StartReading1、Ensure H
Page 24: General ProgrammingIntroductionTher
Page 27: General ProgrammingCommand Programm
Page 30 and 31: General ProgrammingWorking ModeTool
Page 32 and 33: General ProgrammingReading ModeAuto
Page 34 and 35: General ProgrammingReading ModeSens
Page 36 and 37: General ProgrammingReading ModeDela
Page 38 and 39: General ProgrammingSecurity LevelTh
Page 40 and 41: General ProgrammingOthersStart/Stop
Page 42 and 43: Communication ProgrammingIntroducti
Page 44 and 45: Communication ProgrammingSerial Por
Page 50 and 51: Communication ProgrammingKeyboard P
Page 52 and 53: Data FormatIntroduction1D barcodes
Page 54 and 55: Data FormatUser PrefixToolsCode Pro
Page 56 and 57: Data FormatCode ID PrefixBesides AI
Page 58 and 59: Data FormatTerminalToolsCode Progra
Page 60 and 61: SymbolsCode 128Load Factory Default
Page 64 and 65: SymbolsAIM 128ToolsCode Programming
Page 66 and 67: SymbolsEAN-8ToolsCode Programming O
Page 68 and 69:
SymbolsEAN-8ToolsCode Programming O
Page 70 and 71:
SymbolsEAN-13Check DigitToolsCode P
Page 72 and 73:
SymbolsISSNToolsCode Programming ON
Page 74 and 75:
SymbolsISBNToolsCode Programming ON
Page 76 and 77:
SymbolsUPC-ECheck DigitToolsCode Pr
Page 78 and 79:
SymbolsUPC-ETransmit Default “0
Page 80:
SymbolsUPC-ACheck DigitToolsCode Pr
Page 83 and 84:
SymbolsInterleaved 2 of 5Check Digi
Page 85 and 86:
SymbolsITF-6ITF-6 is a fixed length
Page 87 and 88:
SymbolsDeutshe14Load Factory Defaul
Page 89 and 90:
SymbolsCOOP25(Japanese Matrix 2 of
Page 91 and 92:
SymbolsCOOP25(Japanese Matrix 2 of
Page 93 and 94:
SymbolsMatrix 2 of 5( European Matr
Page 95 and 96:
SymbolsIndustrial 25ToolsCode Progr
Page 97 and 98:
SymbolsIndustrial 25ToolsCode Progr
Page 99 and 100:
SymbolsStandard 25Check DigitToolsC
Page 101 and 102:
SymbolsCode 39ToolsCode Programming
Page 103 and 104:
SymbolsCode 39Transmit Start & Stop
Page 105 and 106:
SymbolsCodabarToolsCode Programming
Page 107 and 108:
SymbolsCodabarTransmit Start & Stop
Page 109 and 110:
SymbolsCode 93ToolsCode Programming
Page 111 and 112:
SymbolsCode 93Select Message Length
Page 113 and 114:
SymbolsCode 11Check DigitCode 11 ma
Page 115 and 116:
SymbolsPlesseyToolsCode Programming
Page 117 and 118:
SymbolsPlesseyToolsCode Programming
Page 119 and 120:
SymbolsMSI-PlesseyCheck DigitMSI-Pl
Page 121 and 122:
SymbolsGS1 DatabarToolsCode Program
Page 123 and 124:
AppendixFactory Default ListSymbolC
Page 125 and 126:
AppendixFactory Default ListDeutsch
Page 127 and 128:
AppendixFactory Default ListSend Ch
Page 129 and 130:
AppendixCode ID ListSymbolCode 128U
Page 131 and 132:
AppendixDigit CodeToolsCode Program
Page 133 and 134:
AppendixASCII TableHex Dec Char00 0
Page 135 and 136:
AppendixASCII TableHex Dec Char59 8
show all

NLS-HR100 Series Hand-held 1D Barcode Scanner User ... - Sensis

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?