NLS-HR100 Series Hand-held 1D Barcode Scanner User ... - Sensis

More documents

Recommendations

Info

SymbolsUPC-ECheck DigitToolsCode Programming ONUPC-E is fixed 8 digits barcode and the last digit is check digit. Check digit Code Programming OFFis a value caculated from all digits. It is used for checking if the all 8 digits areright.Transmit Check【Pro CMD:99911004】Do Not Transmit Check【Pro CMD:99911003】UPC-E Code IDCode ID Setting【Pro CMD:99911020】Example of setting UPC-E Code ID to “p” (0x70)1. Read Enable Code Programming barcode.2. Read UPC-E Code ID Setting barcode.3. Read Following <strong>Barcode</strong>s: “7”, and “0”4. Read Save barcode5. Read Disable Code Programming barcode.nlscan.comPage 68
SymbolsUPC-E2 Digits Addenda Code2 Digits Addenda Code is the one to the right of an ordinary code.ToolsCode Programming ONCode Programming OFFDisable 2 Digits Addenda【Pro CMD:99911005】Only Read With 2 digits Addenda Code【Pro CMD:99911007】Enable 2 Digits Addenda Code【Pro CMD:99911006】5 Digits Addenda Code5 Digits Addenda Code is the one to the right of an ordinary code.Disable 5 Digits Addenda Code【Pro CMD:99911010】Only Read With 5 digits Addenda Code【Pro CMD:99911012】Enable 5 Digits Addenda Code【Pro CMD:99911011】“ Enable 2 Digits Addenda Code “ — read an ordinary code and 2 digits Addenda Code.“Disable 2 Digits Addenda Code “ — read an ordinary code only, and ignore 2 digitsAddenda Code.“ Only Read With 2 digits Addenda Code“ — read 2 digits Addenda Code and only readcode with 2 digits Addenda Code.nlscan.comPage 69
Page 5:
Table of ContentsSecurity Level ...
Page 8 and 9:
Table of ContentsCode 39 Code ID ..
Page 10 and 11:
About this guideGraphic NotationsTo
Page 12 and 13:
Getting to StartUnpackingUnpackingU
Page 14 and 15:
Getting to StartCommunication Ports
Page 16 and 17:
Getting to StartConnecting with RS2
Page 18 and 19:
Getting to StartRemoval of Communic
Page 20:
Getting to StartReading1、Ensure H
Page 24:
General ProgrammingIntroductionTher
Page 27: General ProgrammingCommand Programm
Page 30 and 31: General ProgrammingWorking ModeTool
Page 32 and 33: General ProgrammingReading ModeAuto
Page 34 and 35: General ProgrammingReading ModeSens
Page 36 and 37: General ProgrammingReading ModeDela
Page 38 and 39: General ProgrammingSecurity LevelTh
Page 40 and 41: General ProgrammingOthersStart/Stop
Page 42 and 43: Communication ProgrammingIntroducti
Page 44 and 45: Communication ProgrammingSerial Por
Page 50 and 51: Communication ProgrammingKeyboard P
Page 52 and 53: Data FormatIntroduction1D barcodes
Page 54 and 55: Data FormatUser PrefixToolsCode Pro
Page 56 and 57: Data FormatCode ID PrefixBesides AI
Page 58 and 59: Data FormatTerminalToolsCode Progra
Page 60 and 61: SymbolsCode 128Load Factory Default
Page 64 and 65: SymbolsAIM 128ToolsCode Programming
Page 66 and 67: SymbolsEAN-8ToolsCode Programming O
Page 68 and 69: SymbolsEAN-8ToolsCode Programming O
Page 70 and 71: SymbolsEAN-13Check DigitToolsCode P
Page 72 and 73: SymbolsISSNToolsCode Programming ON
Page 74 and 75: SymbolsISBNToolsCode Programming ON
Page 78 and 79: SymbolsUPC-ETransmit Default “0
Page 80: SymbolsUPC-ACheck DigitToolsCode Pr
Page 83 and 84: SymbolsInterleaved 2 of 5Check Digi
Page 85 and 86: SymbolsITF-6ITF-6 is a fixed length
Page 87 and 88: SymbolsDeutshe14Load Factory Defaul
Page 89 and 90: SymbolsCOOP25(Japanese Matrix 2 of
Page 91 and 92: SymbolsCOOP25(Japanese Matrix 2 of
Page 93 and 94: SymbolsMatrix 2 of 5( European Matr
Page 95 and 96: SymbolsIndustrial 25ToolsCode Progr
Page 97 and 98: SymbolsIndustrial 25ToolsCode Progr
Page 99 and 100: SymbolsStandard 25Check DigitToolsC
Page 101 and 102: SymbolsCode 39ToolsCode Programming
Page 103 and 104: SymbolsCode 39Transmit Start & Stop
Page 105 and 106: SymbolsCodabarToolsCode Programming
Page 107 and 108: SymbolsCodabarTransmit Start & Stop
Page 109 and 110: SymbolsCode 93ToolsCode Programming
Page 111 and 112: SymbolsCode 93Select Message Length
Page 113 and 114: SymbolsCode 11Check DigitCode 11 ma
Page 115 and 116: SymbolsPlesseyToolsCode Programming
Page 117 and 118: SymbolsPlesseyToolsCode Programming
Page 119 and 120: SymbolsMSI-PlesseyCheck DigitMSI-Pl
Page 121 and 122: SymbolsGS1 DatabarToolsCode Program
Page 123 and 124: AppendixFactory Default ListSymbolC
Page 125 and 126: AppendixFactory Default ListDeutsch
Page 127 and 128:
AppendixFactory Default ListSend Ch
Page 129 and 130:
AppendixCode ID ListSymbolCode 128U
Page 131 and 132:
AppendixDigit CodeToolsCode Program
Page 133 and 134:
AppendixASCII TableHex Dec Char00 0
Page 135 and 136:
AppendixASCII TableHex Dec Char59 8
show all

NLS-HR100 Series Hand-held 1D Barcode Scanner User ... - Sensis

Create successful ePaper yourself

Delete template?

Save as template?