NLS-HR100 Series Hand-held 1D Barcode Scanner User ... - Sensis

More documents

Recommendations

Info

General ProgrammingWorking ModeToolsCode Programming ONCode Programming OFFShut Down 1【Pro CMD:99900100】Test Mode 4【Pro CMD:99900103】Deep Sleep 2【Pro CMD:99900101】Restart【Pro CMD:99900104】Sleep 3【Pro CMD:99900102】Note:1、 The engine couldn’t be awaked. It must restart or power on.2、It should be awaked by a trigger.3、It could be awaked by communication or a trigger.4、 Use a trigger to quit test mode.All these five modes are temporary. They will disappear and restore to former mode if theengine restarts or powers off.nlscan.comPage 22
General ProgrammingReading ModeHand-held ModeToolsCode Programming ONFactory Default, scan engine will begin to scan when triggered. And when it scanssuccessfully or the trigger is released, the engine will stop scanning.Code Programming OFFHand-held Mode【Pro CMD:99900110】In hand-hald mode, the engine could set Reading a barcode time length.Reading a barcode time length【Pro CMD:99900150】nlscan.comPage 23
Page 5: Table of ContentsSecurity Level ...
Page 8 and 9: Table of ContentsCode 39 Code ID ..
Page 10 and 11: About this guideGraphic NotationsTo
Page 12 and 13: Getting to StartUnpackingUnpackingU
Page 14 and 15: Getting to StartCommunication Ports
Page 16 and 17: Getting to StartConnecting with RS2
Page 18 and 19: Getting to StartRemoval of Communic
Page 20: Getting to StartReading1、Ensure H
Page 24: General ProgrammingIntroductionTher
Page 27: General ProgrammingCommand Programm
Page 32 and 33: General ProgrammingReading ModeAuto
Page 34 and 35: General ProgrammingReading ModeSens
Page 36 and 37: General ProgrammingReading ModeDela
Page 38 and 39: General ProgrammingSecurity LevelTh
Page 40 and 41: General ProgrammingOthersStart/Stop
Page 42 and 43: Communication ProgrammingIntroducti
Page 44 and 45: Communication ProgrammingSerial Por
Page 50 and 51: Communication ProgrammingKeyboard P
Page 52 and 53: Data FormatIntroduction1D barcodes
Page 54 and 55: Data FormatUser PrefixToolsCode Pro
Page 56 and 57: Data FormatCode ID PrefixBesides AI
Page 58 and 59: Data FormatTerminalToolsCode Progra
Page 60 and 61: SymbolsCode 128Load Factory Default
Page 64 and 65: SymbolsAIM 128ToolsCode Programming
Page 66 and 67: SymbolsEAN-8ToolsCode Programming O
Page 68 and 69: SymbolsEAN-8ToolsCode Programming O
Page 70 and 71: SymbolsEAN-13Check DigitToolsCode P
Page 72 and 73: SymbolsISSNToolsCode Programming ON
Page 74 and 75: SymbolsISBNToolsCode Programming ON
Page 76 and 77: SymbolsUPC-ECheck DigitToolsCode Pr
Page 78 and 79: SymbolsUPC-ETransmit Default “0
Page 80:
SymbolsUPC-ACheck DigitToolsCode Pr
Page 83 and 84:
SymbolsInterleaved 2 of 5Check Digi
Page 85 and 86:
SymbolsITF-6ITF-6 is a fixed length
Page 87 and 88:
SymbolsDeutshe14Load Factory Defaul
Page 89 and 90:
SymbolsCOOP25(Japanese Matrix 2 of
Page 91 and 92:
SymbolsCOOP25(Japanese Matrix 2 of
Page 93 and 94:
SymbolsMatrix 2 of 5( European Matr
Page 95 and 96:
SymbolsIndustrial 25ToolsCode Progr
Page 97 and 98:
SymbolsIndustrial 25ToolsCode Progr
Page 99 and 100:
SymbolsStandard 25Check DigitToolsC
Page 101 and 102:
SymbolsCode 39ToolsCode Programming
Page 103 and 104:
SymbolsCode 39Transmit Start & Stop
Page 105 and 106:
SymbolsCodabarToolsCode Programming
Page 107 and 108:
SymbolsCodabarTransmit Start & Stop
Page 109 and 110:
SymbolsCode 93ToolsCode Programming
Page 111 and 112:
SymbolsCode 93Select Message Length
Page 113 and 114:
SymbolsCode 11Check DigitCode 11 ma
Page 115 and 116:
SymbolsPlesseyToolsCode Programming
Page 117 and 118:
SymbolsPlesseyToolsCode Programming
Page 119 and 120:
SymbolsMSI-PlesseyCheck DigitMSI-Pl
Page 121 and 122:
SymbolsGS1 DatabarToolsCode Program
Page 123 and 124:
AppendixFactory Default ListSymbolC
Page 125 and 126:
AppendixFactory Default ListDeutsch
Page 127 and 128:
AppendixFactory Default ListSend Ch
Page 129 and 130:
AppendixCode ID ListSymbolCode 128U
Page 131 and 132:
AppendixDigit CodeToolsCode Program
Page 133 and 134:
AppendixASCII TableHex Dec Char00 0
Page 135 and 136:
AppendixASCII TableHex Dec Char59 8
show all

NLS-HR100 Series Hand-held 1D Barcode Scanner User ... - Sensis

Create successful ePaper yourself

Delete template?

Save as template?