NLS-HR100 Series Hand-held 1D Barcode Scanner User ... - Sensis

More documents

Recommendations

Info

SymbolsMatrix 2 of 5( European Matrix 2 of 5)Load Factory DefaultToolsCode Programming ONCode Programming OFFLoad Matrix 2 of 5 Factory Default【Pro CMD:99912000】Enable/ Disable Matrix 2 of 5Enable Matrix 2 of 5【Pro CMD:99912002】Disable Matrix 2 of 5【Pro CMD:99912001】When the engine can not read Matrix 2 of 5, please read “Enable Matrix 2 of 5” and tryagain.Matrix 2 of 5 Code IDCode ID Setting【Pro CMD:99912010】Example of setting Matrix 2 of 5 Code ID to “p” (0x70)1. Read Enable Code Programming barcode.2. Read Matrix 2 of 5 Code ID Setting barcode.3. Read Following <strong>Barcode</strong>s: “7”, and “0”4. Read Save barcode5. Read Disable Code Programming barcode.nlscan.comPage 84
SymbolsMatrix 2 of 5( European Matrix 2 of 5)Check DigitToolsCode Programming ONMatrix 2 of 5 may include Check Digit (not compulsory) following its barcodemessages. If included, it may be the last digit. It verifies the barcode message.Code Programming OFF» “NO Check, Transmit All” means to read without check and transmitall bytes including barcode message and Check Digit.» “Check, Do Not Transmit Check Digit” means to read and check.If verification is successful, transmits barcode message; if not, engine sendsan error beep.» “Check, Transmit All” means to read and check. If verification issuccessful, transmits all messages; if not, engine sends an error beep.NO Check, Transmit All【Pro CMD:99912003】Check, Transmit All【Pro CMD:99912004】Check, Do Not Transmit Check Digit【Pro CMD:99912005】When “Check, Do Not Transmit Check Digit” is enabled and barcode message lengthminus one is less than Min Message Length, it will lead to error beep.E.g.:Reading a 4-byte (include Check Digit) Matrix 2 of 5 with the Min Message Lengthbeing 4 bytes and “Check, Do Not Transmit Check Digit” enabled leads to error beep.nlscan.comPage 85
Page 5:
Table of ContentsSecurity Level ...
Page 8 and 9:
Table of ContentsCode 39 Code ID ..
Page 10 and 11:
About this guideGraphic NotationsTo
Page 12 and 13:
Getting to StartUnpackingUnpackingU
Page 14 and 15:
Getting to StartCommunication Ports
Page 16 and 17:
Getting to StartConnecting with RS2
Page 18 and 19:
Getting to StartRemoval of Communic
Page 20:
Getting to StartReading1、Ensure H
Page 24:
General ProgrammingIntroductionTher
Page 27:
General ProgrammingCommand Programm
Page 30 and 31:
General ProgrammingWorking ModeTool
Page 32 and 33:
General ProgrammingReading ModeAuto
Page 34 and 35:
General ProgrammingReading ModeSens
Page 36 and 37:
General ProgrammingReading ModeDela
Page 38 and 39:
General ProgrammingSecurity LevelTh
Page 40 and 41:
General ProgrammingOthersStart/Stop
Page 42 and 43: Communication ProgrammingIntroducti
Page 44 and 45: Communication ProgrammingSerial Por
Page 50 and 51: Communication ProgrammingKeyboard P
Page 52 and 53: Data FormatIntroduction1D barcodes
Page 54 and 55: Data FormatUser PrefixToolsCode Pro
Page 56 and 57: Data FormatCode ID PrefixBesides AI
Page 58 and 59: Data FormatTerminalToolsCode Progra
Page 60 and 61: SymbolsCode 128Load Factory Default
Page 64 and 65: SymbolsAIM 128ToolsCode Programming
Page 66 and 67: SymbolsEAN-8ToolsCode Programming O
Page 68 and 69: SymbolsEAN-8ToolsCode Programming O
Page 70 and 71: SymbolsEAN-13Check DigitToolsCode P
Page 72 and 73: SymbolsISSNToolsCode Programming ON
Page 74 and 75: SymbolsISBNToolsCode Programming ON
Page 76 and 77: SymbolsUPC-ECheck DigitToolsCode Pr
Page 78 and 79: SymbolsUPC-ETransmit Default “0
Page 80: SymbolsUPC-ACheck DigitToolsCode Pr
Page 83 and 84: SymbolsInterleaved 2 of 5Check Digi
Page 85 and 86: SymbolsITF-6ITF-6 is a fixed length
Page 87 and 88: SymbolsDeutshe14Load Factory Defaul
Page 89 and 90: SymbolsCOOP25(Japanese Matrix 2 of
Page 91: SymbolsCOOP25(Japanese Matrix 2 of
Page 95 and 96: SymbolsIndustrial 25ToolsCode Progr
Page 97 and 98: SymbolsIndustrial 25ToolsCode Progr
Page 99 and 100: SymbolsStandard 25Check DigitToolsC
Page 101 and 102: SymbolsCode 39ToolsCode Programming
Page 103 and 104: SymbolsCode 39Transmit Start & Stop
Page 105 and 106: SymbolsCodabarToolsCode Programming
Page 107 and 108: SymbolsCodabarTransmit Start & Stop
Page 109 and 110: SymbolsCode 93ToolsCode Programming
Page 111 and 112: SymbolsCode 93Select Message Length
Page 113 and 114: SymbolsCode 11Check DigitCode 11 ma
Page 115 and 116: SymbolsPlesseyToolsCode Programming
Page 117 and 118: SymbolsPlesseyToolsCode Programming
Page 119 and 120: SymbolsMSI-PlesseyCheck DigitMSI-Pl
Page 121 and 122: SymbolsGS1 DatabarToolsCode Program
Page 123 and 124: AppendixFactory Default ListSymbolC
Page 125 and 126: AppendixFactory Default ListDeutsch
Page 127 and 128: AppendixFactory Default ListSend Ch
Page 129 and 130: AppendixCode ID ListSymbolCode 128U
Page 131 and 132: AppendixDigit CodeToolsCode Program
Page 133 and 134: AppendixASCII TableHex Dec Char00 0
Page 135 and 136: AppendixASCII TableHex Dec Char59 8
show all

NLS-HR100 Series Hand-held 1D Barcode Scanner User ... - Sensis

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?