- Page 3: The Gulf Coast Community Design Stu
- Page 10: factoryassembledhomesconstructionpr
- Page 13: Required Equipment: A crane and lif
- Page 17 and 18: DESIGNComponent Homes | 1.2Environm
- Page 19 and 20: PERFORMANCEWind Load: Kits can be d
- Page 21: stall whatever the factory assemble
- Page 24 and 25: panelsconstructionprocessspeeddeliv
- Page 26 and 27: 2.1 | Wood SIPsWood SIPsOverview: S
- Page 28 and 29: 2.1 | Wood SIPsLife Span: The OSB a
- Page 30 and 31: 2.1 | Wood SIPsMM & I Construction
- Page 32 and 33: 2.2 | Non-Wood SIPsand full constru
- Page 34 and 35: 2.2 | Non-Wood SIPssome information
- Page 36: 2.3 | Framed PanelsThe strength of
- Page 39 and 40: Stacked Unit SystemsStacked unit sy
- Page 41 and 42: 3STACKED UNIT SYSTEMSsubjects3.1 In
- Page 43 and 44: should be done carefully, as the co
- Page 45 and 46: Concrete Masonry Units (CMU) | 3.2C
- Page 47 and 48: Concrete Masonry Units (CMU) | 3.2D
- Page 49 and 50: AAC is naturally resistant to termi
- Page 51 and 52: Framing SystemsFraming systems are
- Page 53 and 54: 4FRAMING SYSTEMSsubjects4.1 Convent
- Page 55 and 56: which allows for expedient construc
- Page 57 and 58: Advanced Wood Framing | 4.2Advanced
- Page 59 and 60: esidential building codes but may n
- Page 61 and 62: ut can be designed to carry increas
- Page 63 and 64: Water Resistance: Steel studs are t
- Page 65 and 66:
Engineered Floor Trusses | 4.5Engin
- Page 67 and 68:
Versatility / Flexibility: Engineer
- Page 69 and 70:
equired, construction crews should
- Page 72 and 73:
Chapter 5, Elevated Foundations, is
- Page 74 and 75:
floorsconstructionprocessspeeddeliv
- Page 76 and 77:
6.1 | 2x6 Tongue and Groove Decking
- Page 78 and 79:
6.2 | Suspended Cast-in-Place Decks
- Page 80 and 81:
6.2 | Suspended Cast-in-Place Decks
- Page 82 and 83:
6.3 | Floor FinishesSpeed of Constr
- Page 84 and 85:
6.3 | Floor FinishesGULF COAST AVAI
- Page 86 and 87:
insulationrequiredequipmentthermalp
- Page 88 and 89:
7.1 | Exterior FinishesExterior Fin
- Page 90 and 91:
7.1 | Exterior FinishesEnergy / The
- Page 92 and 93:
7 .2 | SheathingSheathingOverview:
- Page 94 and 95:
7 .2 | SheathingMarket Exposure: OS
- Page 96 and 97:
7.3 | InsulationAfter the foam drie
- Page 98 and 99:
7.3 | InsulationInstallation: Miner
- Page 100 and 101:
7.4 | Interior Finishesthe job and
- Page 102 and 103:
7.4 | Interior FinishesWOOD & WOOD
- Page 104 and 105:
7.4 | Interior FinishesMASONRYStone
- Page 106 and 107:
oofsconstructionprocessspeeddeliver
- Page 108 and 109:
8.1 | Radiant BarriersRoofRadiant b
- Page 110 and 111:
8.1 | Radiant Barrierssometimes rea
- Page 112 and 113:
8.2 | ShinglesEnergy/Thermal: Aspha
- Page 114 and 115:
8.3 | Metal RoofsBecause the screws
- Page 116 and 117:
8.4 | Tile RoofsPERFORMANCETile Roo
- Page 118 and 119:
8.5 | Rubber RoofsINSTALLATIONRubbe
- Page 120 and 121:
8.5 | Rubber RoofsDESIGNEnvironment
- Page 122 and 123:
App. I | Insuring HomesI. Insuring
- Page 124 and 125:
App. II | Energy Efficiency in Home
- Page 126 and 127:
App. II | Energy Efficiency in Home
- Page 128 and 129:
App. III | Site WorkIII. Site WorkT
- Page 130 and 131:
App. IV | Further ResearchIV. Furth
- Page 132 and 133:
App. V | GlossaryCompression: Physi
- Page 134 and 135:
App. V | GlossaryShear Wall: Walls
- Page 136 and 137:
App. VI | EndnotesChapter 3: Cast a
- Page 138 and 139:
App. VI | Endnotes2. “HardiePlank
- Page 140 and 141:
App. VII | Images UsedFig.8Fig.9Fig
- Page 142 and 143:
App. VII | Images UsedFig.16Fig.17I
- Page 144 and 145:
App. VII | Images UsedFig.2Fig.3Fig