CAAPE User's Manual - ALSTOM Signaling Inc.

More documents

Recommendations

Info

Simulator ReferenceBRKSets a breakpoint for the specified logic statement in the current application. Thesimulator halts when this logic statement is encountered.Formats:whereExamples:CHGBRK var-nameBRK &stmt-numvar-name is the name of a result of the equation on which to set the breakpointstmt-num is the hexadecimal statement number of the statement on which to setthe breakpointBRK LAMP-OUT2BRK &1F4Sets a change breakpoint for the specified logic statement in the current application.The simulator halts when the result of this statement changes state.Formats:whereExamples:CHG var-nameCHG &stmt-numvar-name is the name of a result of the equation on which to set the breakpointstmt-num is the hexadecimal statement number of the statement on which to setthe breakpointCHG LAMP-OUT2CHG &1F4P2512A, Rev. Oct/09 12–38 Alstom Signaling Inc.
Simulator ReferenceCLRClears breakpoints, monitors and skips for the current application.Formats:whereExamples:CLR ALL (clears all breakpoints and monitors)CLR BRK (clears all breakpoints)CLR BRK var-name (clears a breakpoint by result name)CLR BRK &stmt-num (clears a breakpoint by statement number)CLR CHG (clears all change breakpoints)CLR CHG var-name (clears a change breakpoint by result name)CLR CHG &stmt-num (clears a change breakpoint by statement number)CLR MON (clears all monitors)CLR MON var-name (clears a monitor by result name)CLR MON &stmt-num (clears a monitor by statement number)CLR SKIP (clears all skips)CLR SKIP var-name (clears a skip by result name)CLR SKIP &stmt-num (clears a skip by statement number)var-name is the name of a result of the equation on which to clear the breakpointstmt-num is the hexadecimal statement number of the statement on which toclear the breakpointCLR ALLCLR BRK LAMP-OUT2CLR BRK &1F4P2512A, Rev. Oct/09 12–39 Alstom Signaling Inc.
Page 3:
Computer-AidedApplicationProgrammin
Page 11 and 12:
MANUAL SPECIAL NOTATIONSIn the Alst
Page 13 and 14:
TopicTABLE OF CONTENTSPage1. SECTIO
Page 15 and 16:
TopicTABLE OF CONTENTS (CONT.)Page6
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
TitleLIST OF FIGURESPageFigure 7-1.
Page 25 and 26:
General1. SECTION 1 - GENERALThis m
Page 27 and 28:
General1.5. COMMON ABBREVIATIONSAbb
Page 29:
GeneralSee Section 11, CAAPE File S
Page 32 and 33:
Introduction2.2.2. System Software
Page 34 and 35:
Introduction2.2.5. CAA VersionsCert
Page 36 and 37:
IntroductionTHIS PAGE INTENTIONALLY
Page 38 and 39:
Getting Started3.2.2. Installation
Page 40 and 41:
Getting StartedThe toolbar is locat
Page 42 and 43:
Getting Started3.6. SETTING USER PR
Page 44 and 45:
Getting StartedTHIS PAGE INTENTIONA
Page 46 and 47:
CAAPE Projects4.1.3. Project Data E
Page 48 and 49:
CAAPE ProjectsThe Component View di
Page 50 and 51:
CAAPE ProjectsProject View, Compone
Page 52 and 53:
CAAPE ProjectsFigure 4-6. Project D
Page 54 and 55:
CAAPE Projects4.5. SETTING PROJECT
Page 56 and 57:
CAAPE ProjectsTHIS PAGE INTENTIONAL
Page 58 and 59:
General Rules and Techniques5.2.2.
Page 60 and 61:
General Rules and Techniques5.4. US
Page 62 and 63:
Using CAAPE GraphicsOnce the applic
Page 64 and 65:
Using CAAPE GraphicsThe available c
Page 66 and 67:
Using CAAPE Graphics6.3. EDITING HA
Page 68 and 69:
Using CAAPE GraphicsFigure 6-4. New
Page 70 and 71:
Using CAAPE Graphics6.3.3. Setting
Page 72 and 73:
Using CAAPE GraphicsFigure 6-8. Sam
Page 74 and 75:
Using CAAPE Graphics6.3.7. Opening
Page 76 and 77:
Using CAAPE GraphicsNon-Vital Seria
Page 78 and 79:
Using CAAPE Graphics6.5. EDITING LO
Page 80 and 81:
Using CAAPE GraphicsEquation parame
Page 82 and 83:
Using CAAPE Graphics6.5.3.2. Using
Page 84 and 85:
Using CAAPE Graphics6.5.3.5. Using
Page 86 and 87:
Using CAAPE Graphics6.5.4. Insertin
Page 88 and 89:
Using CAAPE Graphics6.5.5. Editing
Page 90 and 91:
Using CAAPE Graphics6.5.6.7. Transf
Page 92 and 93:
Using CAAPE Graphics6.5.6.10.3. Com
Page 94 and 95:
Using CAAPE GraphicsFigure 6-17. Lo
Page 96 and 97:
Using CAAPE Graphics6.5.12. Cut & P
Page 98 and 99:
Using CAAPE Graphics6.7. USING THE
Page 100 and 101:
Using CAAPE Graphics6.8. CREATING A
Page 102 and 103:
Using CAAPE GraphicsEnter the descr
Page 104 and 105:
Using CAAPE GraphicsFigure 6-26. Sy
Page 106 and 107:
Using CAAPE Graphics− VSC boards
Page 108 and 109:
Using CAAPE GraphicsIn the Serial M
Page 110 and 111:
Using CAAPE Graphics6.8.5. Saving a
Page 112 and 113:
Using CAAPE GraphicsFigure 6-31. Me
Page 114 and 115:
Using CAAPE GraphicsTo build applic
Page 116 and 117:
Using CAAPE Graphics6.10. IMPORTING
Page 118 and 119:
Using CAAPE Graphics6.10.5. Creatin
Page 120 and 121:
Using Application FilesThere can al
Page 122 and 123:
Using Application Files7.4.1. Appli
Page 124 and 125:
Using Application FilesFigure 7-2.
Page 126 and 127:
Using Application Files7.5. EDITING
Page 128 and 129:
Using Application Files7.6.1. Creat
Page 130 and 131:
Using Application FilesWhen adding
Page 132 and 133:
Using Application Files7.7. SETTING
Page 134 and 135:
Using Application FilesAvailable ru
Page 136 and 137:
Using Application Files7.8. COMPILI
Page 138 and 139:
Using Application Files7.8.2. VPI2,
Page 140 and 141:
Using Application Files7.8.3. VPI2,
Page 142 and 143:
Using Application Files7.8.4.1. EPR
Page 144 and 145:
Using Application Files7.9. SIMULAT
Page 146 and 147:
Using Application Files7.10.2. Veri
Page 148 and 149:
Using Application Files7.10.6. Grap
Page 150 and 151:
Using Application FilesFiles: syste
Page 152 and 153:
Using Application FilesVPI VSCVital
Page 154 and 155:
Using Application FilesCenTraCode I
Page 156 and 157:
Using Application Files7.13. PRINTI
Page 158 and 159:
Using Application Files7.13.3.2. Pr
Page 160 and 161:
Using Application FilesUse the Page
Page 162 and 163:
Using Application Files7.13.4. Rela
Page 164 and 165:
Configuration Control8.2.2. Running
Page 166 and 167:
Configuration Control9.2.2. Configu
Page 168 and 169:
Configuration Control9.2.4. Compile
Page 170 and 171:
Configuration ControlIndividual CAA
Page 172 and 173:
Using the Graphical Simulator10.1.2
Page 174 and 175:
Using the Graphical Simulator10.5.
Page 176 and 177:
Page 178 and 179:
Page 180 and 181:
Page 182 and 183:
Page 184 and 185:
Page 186 and 187:
Using the Graphical SimulatorUse th
Page 188 and 189:
Using the Graphical SimulatorUse th
Page 190 and 191:
Using the Graphical SimulatorNOTETh
Page 192 and 193:
Page 194 and 195:
Page 196 and 197:
Page 198 and 199:
Page 200 and 201:
Page 202 and 203:
Page 204 and 205:
Page 206 and 207:
Page 208 and 209:
Page 210 and 211:
Page 212 and 213:
Page 214 and 215:
Page 216 and 217:
Page 218 and 219:
Page 220 and 221:
Page 222 and 223:
Page 224 and 225:
Page 226 and 227:
Page 228 and 229:
Using the Graphical SimulatorTHIS P
Page 230 and 231: CAAPE File Infrastructure11.3. CAA
Page 232 and 233: CAAPE File InfrastructureApplicatio
Page 234 and 235: CAAPE File InfrastructureTable 11-6
Page 242 and 243: CAAPE File InfrastructureTHIS PAGE
Page 244 and 245: Simulator Reference12.2. APPLICATIO
Page 246 and 247: Simulator Reference12.2.4. Symbol T
Page 248 and 249: Simulator ReferenceFor example (use
Page 250 and 251: Simulator Reference12.2.7. Hardware
Page 252 and 253: Simulator Reference12.2.7.3. Switch
Page 254 and 255: Simulator Reference12.2.7.4.1. Prot
Page 256 and 257: Simulator ReferenceFor example:1 2
Page 258 and 259: Simulator ReferenceTable 12-2. Mess
Page 260 and 261: Simulator Reference12.3. SIMULATION
Page 262 and 263: Simulator Reference}ELSE{}{BOOL VAR
Page 264 and 265: Simulator Reference12.4.2. Non-Vita
Page 266 and 267: Simulator ReferenceFunction: SET_NV
Page 268 and 269: Simulator ReferenceFunction: SET_NV
Page 270 and 271: Simulator Reference12.5. PROTOCOL D
Page 272 and 273: Simulator ReferenceON_NVSER_RECEIVE
Page 274 and 275: Simulator ReferenceON_NVTWC_RECEIVE
Page 276 and 277: Simulator Reference12.6. SCRIPT FIL
Page 278 and 279: Simulator Reference12.6.4. Alphabet
Page 282 and 283: Simulator ReferenceCYCExecute the a
Page 284 and 285: Simulator ReferenceFLIPReverses the
Page 286 and 287: Simulator ReferenceLOAD / NLOADSets
Page 288 and 289: Simulator ReferenceMAXSet the maxim
Page 290 and 291: Simulator ReferencePAUSECauses the
Page 292 and 293: Simulator ReferenceRESETResets cert
Page 294 and 295: Simulator ReferenceSETSets the valu
Page 296 and 297: Simulator ReferenceSIMExecute the a
Page 298 and 299: Simulator ReferenceTRACESets condit
Page 300 and 301: Simulator Reference12.6.5. Command
Page 302 and 303: Simulator ReferenceTable 12-4. Appl
Page 304: Simulator Reference12.6.7. Special
show all

CAAPE User's Manual - ALSTOM Signaling Inc.

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?