Installation Operation and Maintenance Manual

More documents

Recommendations

Info

Maintenance (Continued).030101For more information on how to set the impeller clearances, refer to the Impeller-clearance checks andImpeller-clearance setting sections in Commissioning, Startup, Operation, and Shutdown.Attach the i-ALERT Condition Monitor to the pumpCAUTION:Always wear protective gloves. The pump and condition monitor can be hot.Tools required:• 5/32 inch hex wrench1. Attach the condition monitor (761B) to the bearing frame (228A) using the hex-head screw (372T)provided.761B372T228A2. Tighten the hex-head screw with a 5/32 inch hex wrench to 6 ft-lbs (8 Nm).108 Model 3796 i-FRAME Installation, Operation, and Maintenance Manual
Maintenance (Continued)Post-assembly checksPerform these checks after you assemble the pump, then continue with pump startup:• Rotate the shaft by hand in order to make sure that it rotates easily and smoothly and that there is norubbing.• Open the isolation valves and check the pump for leaks.Install the back pull-out assembly (except HT 3196)CAUTION:Never remove the back pull-out assembly without assistance.1. Clean the casing fit and install the casing gasket (351) on the seal chamber and stuffing-box cover.2. Loosen the clamping bolts (370C) and jack bolts (370D) on the bearing housing.423370C370D3. Install the back pull-out assembly in the casing.Model 3796 i-FRAME Installation, Operation, and Maintenance Manual 109
Page 1:
Goulds PumpsInstallation, Operation
Page 4 and 5:
Table of ContentsImpeller-clearance
Page 6 and 7:
Introduction and SafetyIntroduction
Page 8 and 9:
Introduction and Safety (Continued)
Page 10 and 11:
Page 12 and 13:
Page 14 and 15:
Page 16 and 17:
Page 18 and 19:
Page 20 and 21:
Transportation and Storage (Continu
Page 22 and 23:
Product DescriptionProduct Descript
Page 24 and 25:
Product Description (Continued)Cove
Page 26 and 27:
Product Description (Continued)Tabl
Page 28 and 29:
InstallationInstallationPreinstalla
Page 30 and 31:
Installation (Continued)Piping chec
Page 32 and 33:
Installation (Continued)Liquid sour
Page 34 and 35:
Installation (Continued)Example: Di
Page 36 and 37:
Installation (Continued)d) Make sur
Page 38 and 39:
Installation (Continued)76152341. U
Page 40 and 41:
Installation (Continued)Baseplate-l
Page 42 and 43:
Installation (Continued)WhenPeriodi
Page 44 and 45:
Installation (Continued)1. Set the
Page 46 and 47:
Installation (Continued)C-face adap
Page 48 and 49:
Commissioning, Startup, Operation,
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58 and 59:
Page 60 and 61: Commissioning, Startup, Operation,
Page 66 and 67: MaintenanceMaintenanceMaintenance s
Page 68 and 69: Maintenance (Continued)Regrease the
Page 70 and 71: Maintenance (Continued)Packed stuff
Page 72 and 73: Maintenance (Continued)1. Is your b
Page 74 and 75: Maintenance (Continued)Clean surfac
Page 76 and 77: Maintenance (Continued)5. Remove th
Page 78 and 79: Maintenance (Continued)3. Remove th
Page 80 and 81: Maintenance (Continued)134236A370D4
Page 82 and 83: Maintenance (Continued)253B168A4961
Page 84 and 85: Maintenance (Continued)2. Loosen th
Page 86 and 87: Maintenance (Continued)Surface insp
Page 88 and 89: Maintenance (Continued)444Figure 24
Page 90 and 91: Maintenance (Continued)Bearing fits
Page 92 and 93: Maintenance (Continued)168361A12238
Page 94 and 95: Maintenance (Continued)372T 113A 40
Page 96 and 97: Maintenance (Continued)a) Coat the
Page 98 and 99: Maintenance (Continued)13411. Prepa
Page 100 and 101: Maintenance (Continued)4. Check the
Page 102 and 103: Maintenance (Continued)333AINPRO la
Page 104 and 105: Maintenance (Continued)Seal the sha
Page 106 and 107: Maintenance (Continued)c) Install t
Page 108 and 109: Maintenance (Continued)126412A101In
Page 112 and 113: Maintenance (Continued)100351418100
Page 114 and 115: Maintenance (Continued)Table 18: Ma
Page 116 and 117: Maintenance (Continued)Table 22: Lu
Page 118 and 119: TroubleshootingTroubleshootingOpera
Page 120 and 121: Troubleshooting (Continued)i-ALERT
Page 122 and 123: Parts Listings and Cross-Sectional
Page 132: Other Relevant Documentation or Man
show all

Installation Operation and Maintenance Manual

Create successful ePaper yourself

Delete template?

Save as template?