Installation Operation and Maintenance Manual

More documents

Recommendations

Info

Maintenance (Continued)253B168A496112A1347. Remove the bearing housing O-ring (496) and the inboard bearing (168A).122253B168A136382248A112A8. Remove the bearing locknut (136) and the bearing lockwasher (382).9. Remove the outboard bearings (112A) and the clamp ring (253B).NOTICE: Do not remove the oil flinger unless it is damaged. Doing so may result in unnecessaryshutdown time or equipment damage.NOTICE: Use force only on the inner race when you press bearings off the shaft. Do not use forcein situations in which you might break a part. Doing so may result in equipment damage.NOTICE:Save the bearings for inspection. Do not reuse the bearings. Doing so may result in decreasedperformance.10. Remove the outboard labyrinth oil seal (332A) from the bearing housing (134).11. Remove the O-rings (497F and 497G) if it is necessary.Labyrinth oil-seal O-rings are part of the 3196 maintenance kits, and they are sold separately.497G134497F332ADisassemble the bearing frame1. Remove these plugs from the bearing frame (228A).80 Model 3796 i-FRAME Installation, Operation, and Maintenance Manual
Maintenance (Continued)• oil-fill plug (113A)• oil-drain plug (408A)• sight-oiler plug (408J)• four oil mist/grease connection plugs (408H)• oil-cooler inlet and outlet plugs (408L and 408M) or oil cooler2. For the MTi and LTi models, remove the bearing frame foot-to-frame bolts (370F) and the frame foot(241).408W761B372T 113A 408W408N319408M408N408A370F241Guidelines for i-ALERT Condition Monitor disposalPrecautionsWARNING:• Never heat the condition monitor to temperatures in excess of 300°F (149°C). Heating to thesetemperatures could result in death or serious injury.• Never dispose of the condition monitor in a fire. This could result in death or serious injury.GuidelinesThe battery contained in the condition monitor does not contain enough lithium to qualify as reactivehazardous waste. Use these guidelines when disposing of the condition monitor.• The condition monitor is safe for disposal in the normal municipal waste stream.• Adhere to local laws when you dispose of the condition monitor.Disassemble the C-face adapterNOTICE: You must properly support the motor with a clean, uncorroded eye bolt or a strap under bothend bells. Failure to do so may result in equipment damage.1. Loosen the motor-mounting bolts and remove the motor.This table shows the number of motor-mounting bolts.Table 11: Required number of motor-mounting boltsPump frame Motor frame Number of boltsSTi All 4MTi and LTi 143-286 4324-365 8Model 3796 i-FRAME Installation, Operation, and Maintenance Manual 81
Page 1:
Goulds PumpsInstallation, Operation
Page 4 and 5:
Table of ContentsImpeller-clearance
Page 6 and 7:
Introduction and SafetyIntroduction
Page 8 and 9:
Introduction and Safety (Continued)
Page 10 and 11:
Page 12 and 13:
Page 14 and 15:
Page 16 and 17:
Page 18 and 19:
Page 20 and 21:
Transportation and Storage (Continu
Page 22 and 23:
Product DescriptionProduct Descript
Page 24 and 25:
Product Description (Continued)Cove
Page 26 and 27:
Product Description (Continued)Tabl
Page 28 and 29:
InstallationInstallationPreinstalla
Page 30 and 31:
Installation (Continued)Piping chec
Page 32 and 33: Installation (Continued)Liquid sour
Page 34 and 35: Installation (Continued)Example: Di
Page 36 and 37: Installation (Continued)d) Make sur
Page 38 and 39: Installation (Continued)76152341. U
Page 40 and 41: Installation (Continued)Baseplate-l
Page 42 and 43: Installation (Continued)WhenPeriodi
Page 44 and 45: Installation (Continued)1. Set the
Page 46 and 47: Installation (Continued)C-face adap
Page 48 and 49: Commissioning, Startup, Operation,
Page 66 and 67: MaintenanceMaintenanceMaintenance s
Page 68 and 69: Maintenance (Continued)Regrease the
Page 70 and 71: Maintenance (Continued)Packed stuff
Page 72 and 73: Maintenance (Continued)1. Is your b
Page 74 and 75: Maintenance (Continued)Clean surfac
Page 76 and 77: Maintenance (Continued)5. Remove th
Page 78 and 79: Maintenance (Continued)3. Remove th
Page 80 and 81: Maintenance (Continued)134236A370D4
Page 84 and 85: Maintenance (Continued)2. Loosen th
Page 86 and 87: Maintenance (Continued)Surface insp
Page 88 and 89: Maintenance (Continued)444Figure 24
Page 90 and 91: Maintenance (Continued)Bearing fits
Page 92 and 93: Maintenance (Continued)168361A12238
Page 94 and 95: Maintenance (Continued)372T 113A 40
Page 96 and 97: Maintenance (Continued)a) Coat the
Page 98 and 99: Maintenance (Continued)13411. Prepa
Page 100 and 101: Maintenance (Continued)4. Check the
Page 102 and 103: Maintenance (Continued)333AINPRO la
Page 104 and 105: Maintenance (Continued)Seal the sha
Page 106 and 107: Maintenance (Continued)c) Install t
Page 108 and 109: Maintenance (Continued)126412A101In
Page 110 and 111: Maintenance (Continued).030101For m
Page 112 and 113: Maintenance (Continued)100351418100
Page 114 and 115: Maintenance (Continued)Table 18: Ma
Page 116 and 117: Maintenance (Continued)Table 22: Lu
Page 118 and 119: TroubleshootingTroubleshootingOpera
Page 120 and 121: Troubleshooting (Continued)i-ALERT
Page 122 and 123: Parts Listings and Cross-Sectional
Page 132:
Other Relevant Documentation or Man
show all

Installation Operation and Maintenance Manual

Create successful ePaper yourself

Delete template?

Save as template?