Installation Operation and Maintenance Manual

More documents

Recommendations

Info

Introduction and Safety (Continued)Hazard levelsHazard levelDANGER:IndicationA hazardous situation which, if not avoided, willresult in death or serious injuryWARNING:A hazardous situation which, if not avoided, couldresult in death or serious injuryCAUTION:A hazardous situation which, if not avoided, couldresult in minor or moderate injuryNOTICE:• A potential situation which, if not avoided,could result in undesirable conditions• A practice not related to personal injuryHazard categoriesHazard categories can either fall under hazard levels or let specific symbols replace the ordinary hazardlevel symbols.Electrical hazards are indicated by the following specific symbol:Electrical Hazard:Environmental safetyThese are examples of other categories that can occur. They fall under the ordinary hazard levels and mayuse complementing symbols:• Crush hazard• Cutting hazard• Arc flash hazardThe work areaAlways keep the pump station clean to avoid and/or discover emissions.Recycling guidelinesWaste and emissions regulationsAlways recycle according to these guidelines:1. If the unit or parts are accepted by an authorized recycling company, then follow local recycling lawsand regulations.2. If the unit or parts are not accepted by an authorized recycling company, then return them to thenearest ITT representative.Observe these safety regulations regarding waste and emissions:• Dispose appropriately of all waste.• Handle and dispose of the pumped fluid in compliance with applicable environmental regulations.• Clean up all spills in accordance with safety and environmental procedures.• Report all environmental emissions to the appropriate authorities.6 Model 3796 i-FRAME Installation, Operation, and Maintenance Manual
Introduction and Safety (Continued)Reference for electrical installationFor electrical installation requirements, consult your local electric utility.User health and safetySafety equipmentThe work areaUse safety equipment according to the company regulations. Use this safety equipment within the workarea:• Helmet• Safety goggles (with side shields)• Protective shoes• Protective gloves• Gas mask• Hearing protectionObserve these regulations and warnings in the work area:• Always keep the work area clean.• Pay attention to the risks presented by gas and vapors in the work area.• Avoid all electrical dangers. Pay attention to the risks of electric shock or arc flash hazards.Product and product positioning requirementsElectrical connections regulationsEarthing (grounding)Observe these requirements for the product and the product positioning:WARNING:• Only use fasteners of the proper size and material.• Replace all corroded fasteners.• Make sure that all fasteners are properly tightened and that there are no missing fasteners.• Never operate a pump unless safety devices are installed.• Never operate a pump unless a coupling guard is installed.• Never force the piping in order to make a connection with a pump.• Never start a pump without the proper priming.• Never start a pump without the proper liquid level in self-priming pumps.• Never run a pump below the minimum rated flow or with any suction or discharge valve closed.Electrical connections must be made by certified electricians in compliance with all international, national,state, and local regulations.Observe these guidelines and warnings for electrical connections:• Make sure that the product is isolated from the power supply and cannot be energized by mistake.This guideline also applies to the control circuit.• Make sure that the thermal contacts are connected to a protection circuit according to the productapprovals, and that they are in use.All electric equipment must be earthed (grounded). This rule applies to pumps and mixers as well asmonitoring equipment.Precautions before workObserve these safety precautions before you work with the product or are in connection with the product:• Provide a suitable barrier around the work area, for example, a guard rail.• Make sure that all safety guards are in place and secure.• Make sure that the equipment is properly insulated when it operates at extreme temperatures.• Allow all system and pump components to cool before you handle them.Model 3796 i-FRAME Installation, Operation, and Maintenance Manual 7
Page 1: Goulds PumpsInstallation, Operation
Page 4 and 5: Table of ContentsImpeller-clearance
Page 6 and 7: Introduction and SafetyIntroduction
Page 10 and 11: Introduction and Safety (Continued)
Page 20 and 21: Transportation and Storage (Continu
Page 22 and 23: Product DescriptionProduct Descript
Page 24 and 25: Product Description (Continued)Cove
Page 26 and 27: Product Description (Continued)Tabl
Page 28 and 29: InstallationInstallationPreinstalla
Page 30 and 31: Installation (Continued)Piping chec
Page 32 and 33: Installation (Continued)Liquid sour
Page 34 and 35: Installation (Continued)Example: Di
Page 36 and 37: Installation (Continued)d) Make sur
Page 38 and 39: Installation (Continued)76152341. U
Page 40 and 41: Installation (Continued)Baseplate-l
Page 42 and 43: Installation (Continued)WhenPeriodi
Page 44 and 45: Installation (Continued)1. Set the
Page 46 and 47: Installation (Continued)C-face adap
Page 48 and 49: Commissioning, Startup, Operation,
Page 58 and 59:
Commissioning, Startup, Operation,
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
MaintenanceMaintenanceMaintenance s
Page 68 and 69:
Maintenance (Continued)Regrease the
Page 70 and 71:
Maintenance (Continued)Packed stuff
Page 72 and 73:
Maintenance (Continued)1. Is your b
Page 74 and 75:
Maintenance (Continued)Clean surfac
Page 76 and 77:
Maintenance (Continued)5. Remove th
Page 78 and 79:
Maintenance (Continued)3. Remove th
Page 80 and 81:
Maintenance (Continued)134236A370D4
Page 82 and 83:
Maintenance (Continued)253B168A4961
Page 84 and 85:
Maintenance (Continued)2. Loosen th
Page 86 and 87:
Maintenance (Continued)Surface insp
Page 88 and 89:
Maintenance (Continued)444Figure 24
Page 90 and 91:
Maintenance (Continued)Bearing fits
Page 92 and 93:
Maintenance (Continued)168361A12238
Page 94 and 95:
Maintenance (Continued)372T 113A 40
Page 96 and 97:
Maintenance (Continued)a) Coat the
Page 98 and 99:
Maintenance (Continued)13411. Prepa
Page 100 and 101:
Maintenance (Continued)4. Check the
Page 102 and 103:
Maintenance (Continued)333AINPRO la
Page 104 and 105:
Maintenance (Continued)Seal the sha
Page 106 and 107:
Maintenance (Continued)c) Install t
Page 108 and 109:
Maintenance (Continued)126412A101In
Page 110 and 111:
Maintenance (Continued).030101For m
Page 112 and 113:
Maintenance (Continued)100351418100
Page 114 and 115:
Maintenance (Continued)Table 18: Ma
Page 116 and 117:
Maintenance (Continued)Table 22: Lu
Page 118 and 119:
TroubleshootingTroubleshootingOpera
Page 120 and 121:
Troubleshooting (Continued)i-ALERT
Page 122 and 123:
Parts Listings and Cross-Sectional
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132:
Other Relevant Documentation or Man
show all

Installation Operation and Maintenance Manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?