Installation Operation and Maintenance Manual

More documents

Recommendations

Info

Product DescriptionProduct DescriptionGeneral description 3796The 3796 is a horizontal overhung, self-priming, open impeller, centrifugal pump.This model is based on 3 power ends and 8 hydraulic pump sizes.Figure 5: 3796 pumpThis table shows the number of hydraulic sizes available for each drive-unit size group.Pump size groupNumber of hydraulic sizesSTi 2MTi 6LTi 620 Model 3796 i-FRAME Installation, Operation, and Maintenance Manual
Product Description (Continued)Part description 3796Casing Impeller Cover Power end31963796HT 3196CV 3196LF 3196NM 31963198Figure 6: 3796 part descriptionThis table describes the pump casing parts.Table 3: CasingPartDischargeCasing ventilationPriming chamberGasketMounting methodStandard flangeOptional heaterDescriptionTop-centerlineSelf-ventingintegrally cast allowing the pump to evacuate air to prime itselffully confinedIntegral foot support for maximum resistance to misalignment and distortion dueto piping loadsANSI class 150 raised-face serrated flangeImmersion heater to prevent the liquid in the priming chamber from freezing inoutdoor applicationsImpellerThe impeller is• fully open• screwed onto the shaftThe threads are sealed from the pumped liquid by a Teflon O-ring.Model 3796 i-FRAME Installation, Operation, and Maintenance Manual 21
Page 1: Goulds PumpsInstallation, Operation
Page 4 and 5: Table of ContentsImpeller-clearance
Page 6 and 7: Introduction and SafetyIntroduction
Page 8 and 9: Introduction and Safety (Continued)
Page 20 and 21: Transportation and Storage (Continu
Page 24 and 25: Product Description (Continued)Cove
Page 26 and 27: Product Description (Continued)Tabl
Page 28 and 29: InstallationInstallationPreinstalla
Page 30 and 31: Installation (Continued)Piping chec
Page 32 and 33: Installation (Continued)Liquid sour
Page 34 and 35: Installation (Continued)Example: Di
Page 36 and 37: Installation (Continued)d) Make sur
Page 38 and 39: Installation (Continued)76152341. U
Page 40 and 41: Installation (Continued)Baseplate-l
Page 42 and 43: Installation (Continued)WhenPeriodi
Page 44 and 45: Installation (Continued)1. Set the
Page 46 and 47: Installation (Continued)C-face adap
Page 48 and 49: Commissioning, Startup, Operation,
Page 66 and 67: MaintenanceMaintenanceMaintenance s
Page 68 and 69: Maintenance (Continued)Regrease the
Page 70 and 71: Maintenance (Continued)Packed stuff
Page 72 and 73:
Maintenance (Continued)1. Is your b
Page 74 and 75:
Maintenance (Continued)Clean surfac
Page 76 and 77:
Maintenance (Continued)5. Remove th
Page 78 and 79:
Maintenance (Continued)3. Remove th
Page 80 and 81:
Maintenance (Continued)134236A370D4
Page 82 and 83:
Maintenance (Continued)253B168A4961
Page 84 and 85:
Maintenance (Continued)2. Loosen th
Page 86 and 87:
Maintenance (Continued)Surface insp
Page 88 and 89:
Maintenance (Continued)444Figure 24
Page 90 and 91:
Maintenance (Continued)Bearing fits
Page 92 and 93:
Maintenance (Continued)168361A12238
Page 94 and 95:
Maintenance (Continued)372T 113A 40
Page 96 and 97:
Maintenance (Continued)a) Coat the
Page 98 and 99:
Maintenance (Continued)13411. Prepa
Page 100 and 101:
Maintenance (Continued)4. Check the
Page 102 and 103:
Maintenance (Continued)333AINPRO la
Page 104 and 105:
Maintenance (Continued)Seal the sha
Page 106 and 107:
Maintenance (Continued)c) Install t
Page 108 and 109:
Maintenance (Continued)126412A101In
Page 110 and 111:
Maintenance (Continued).030101For m
Page 112 and 113:
Maintenance (Continued)100351418100
Page 114 and 115:
Maintenance (Continued)Table 18: Ma
Page 116 and 117:
Maintenance (Continued)Table 22: Lu
Page 118 and 119:
TroubleshootingTroubleshootingOpera
Page 120 and 121:
Troubleshooting (Continued)i-ALERT
Page 122 and 123:
Parts Listings and Cross-Sectional
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132:
Other Relevant Documentation or Man
show all

Installation Operation and Maintenance Manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?