BIG KAISER High Performance Tooling Solutions 2018-2019

HYDRAULIC CHUCKS
Catalog
Number
Fig. ød øD øD1 øD2 L L1 L2 H
Min Clamping
Length E
Adjusting
Screw
Weight
(lbs.)
BBT30-HDC6-45 1
1.181 1.81
1.77 .28
1.38-1.97
HDA6-05020 1.5
—
—
-75 2
2.95 1.57
6mm
1.10
1.8
-90
1.024 1.79
3.54
2.24 1.10-1.97 HDA6-05032
3 1.22
1.69
-105 4.13 2.83 2.0
-HDC8-45 1
1.260 1.81
1.77 .28
1.38-1.97
HDA8-06020 1.5
—
—
-75 2
2.95 1.61
1.8
8mm
1.10
-90
1.102 1.79
3.54
2.24 1.10-1.97 HDA8-06032
3 1.30
1.73
2.0
-105 4.13 2.83
-HDC10-45 1
1.339
1.77 .28
1.77-2.17
HDA10-08015 1.5
—
—
-75 2
2.95
2.0
10mm
1.81
1.30
-90
1.181
1.30 3.54 1.42 2.01 1.30-2.17 HDA10-08032
3
2.2
-105 1.42 4.13 2.60
-HDC12-45 1
1.417
—
1.77 .28 — 2.17-2.36
HDA12-10010• 1.5
-75 2
2.95 1.42
1.8
12mm
1.81
1.50
-90
1.260
1.38 3.54
2.01 1.50-2.36 HDA12-10032 2.0
3
1.77
-105 1.50 4.13 2.64 2.2
-HDC14-90 3 14mm 1.339 1.81 1.46 3.54 1.81 2.05 1.50-2.36 1.50 HDA12-10032 2.0
-HDC16-45 1
1.654
1.77 .28
2.76
— 1.5
-75 2
2.95 1.38
HDA16-12030 2.0
16mm
1.81 —
—
1.69
-90
1.496
3.54
1.69-2.76
2.2
3
1.85 HDA16-12037
-150 5.91 2.3
-HDC20-60
— 2.36 — .55 1.69-2.13
HDA16-12030 2.0
-75 4
2.09 1.81 2.95 .63 1.02 1.81-2.76
20mm 1.496
1.69
-90 3.54 1.22 1.61
2.4
1.69-2.76 HDA16-12037
-150 3 1.81 — 5.91 1.57 — 2.2
-HDC25-105 4 25mm 2.165 2.48 — 4.13 1.73 — 2.05-3.15 2.05 HDA25-16039 3.8
-HDC32-105 4 32mm 2.362 2.95 — 4.13 1.54 — 2.20-3.15 2.20 HDA25-16039 4.0
A.2 BBT/BT
• “H” indicates the adjustment length with an adjusting screw
• Adjusting screws cannot be used with models marked
• Straight collets cannot be used with models marked
• In case the projection length needs to be adjusted from the shank side, add the letter “W” to adjusting screw model number for hexagon sockets on both sides
(ex: HDA6-05020W), adjusting screw with •indication is not available in W type
!
CAUTION
Use only cutting tools that have a shank tolerance of h6 (see table Pg. 26). Do not use with cutting tools
made with a flat on the shank (ie: Weldon type shank). Roughing end mills are not recommended for use
with HYDRAULIC CHUCKS. Do not tighten the clamping screw without first inserting a cutting tool into the
tool holder. Always insert the cutting tool into the hydraulic tool holder beyond min. clamping length “E”.
ACCESSORIES
PERFECT SEAL/
JET COLLET
PG. 361
127