BIG KAISER High Performance Tooling Solutions 2018-2019

HYDRAULIC CHUCK
Catalog
Number
Fig. ød øD øD1 L L1 H
Min Clamping
Length E
Adjusting
Screw
Max
RPM
Weight
(lbs.)
HSK-A63-HDC14-85
3.35 1.57 2.36
-120 14mm 1.340
4.72
1.50
15,000 3.1
1.77 1.50-2.28 HDA12-10025
-150 5.90 3.7
-HDC16-90
-120 16mm 1.500
4.72 1.81 2.28-2.68 HDA16-12015 3.3
-150 5.90 1.69-2.68 HDA16-12037 4.2
-HDC18-90
2
1.97
3.54
2.56 HDA16-12037 2.9
-HDC20-90
• Coolant pipe must be ordered separately
• “H” indicates the adjustment length with an adjusting screw
• “H” dimension is the Max tool shank length that can be inserted into the holder
• Do not attempt to balance before first consulting BIG KAISER
• In case the projection length needs to be adjusted from the shank side, add the letter “W”
to adjusting screw model number for hexagon sockets on both sides (ex: HDA6-05020W)
• Adjusting screws cannot be used with models marked
• Straight collet cannot be used with models marked
3.54
-120 18mm 1.570
4.72 1.81 2.28-3.68 1.69 HDA20-16015 3.5
13,000
-150 5.90 1.69-2.68 HDA25-16039 4.4
3.54
-120 20mm 1.650
4.72 1.89 2.28-2.68 HDA20-16015 3.5
2.56
2.56 — 2.9
-150 5.90 1.69-2.68 HDA25-16039 4.4
-HDC25-120
25mm 2.170 2.48 4.72 2.01 3.74 2.05
4.6
3
—
-HDC32-125 32mm 2.360 2.95 4.92 2.32 3.94 2.20 12,000 5.3
HSK-A100-HDC.750-4 2 .750 1.654 — 4.00 2.00 1.69-2.76 1.69 HDA16-12037 13,000 6.0
ACCESSORIES
-HDC1.000-4 3 1.000 2.480 — 4.00 3.54 2.05-3.15 2.05 HDA25-16039 13,000 7.3
-HDC1.250-4.5 3 1.250 2.717 — 4.50 3.58 2.20-3.15 2.20 HDA25-16039 12,000 8.2
-HDC6-75
2.95 1.02 1.81
-120 6mm 1.020
4.72
17,000 5.7
1.73 1.10-1.89 HDA6-05032
-165 6.50 6.4
1.10
-HDC8-75
2.95 1.02 1.81 —
5.3
-120 8mm 1.100
4.72
5.7
1.73 1.10-1.89 HDA8-06032
-165 6.50 6.6
15,000
-HDC10-90
3.54 1.65 2.40
— 5.5
-120 10mm 1.188
4.72
1.30
6.0
1.77 1.30-2.09 HDA10-08032
-165 6.50 6.8
1.97
-HDC12-95
3.74
2.48
—
5.5
4
-120 12mm 1.260
4.72 1.85
1.50 HDA12-10025 6.0
1.50-2.28
-165 6.50 HDA12-10032 6.8
-HDC16-100
3.94
-135 16mm 1.500
5.31 2.09
HDA16-12030 6.6
1.69-2.68
13,000
-165 6.50 HDA16-12037 7.3
1.69
-HDC20-105
4.13
2.87 — 6.0
2.68
!
—
—
—
CAUTION
Use only cutting tools that have a shank tolerance of h6
(see table Pg. 26). Do not use with cutting tools made with
a flat on the shank (ie: Weldon type shank). Roughing
end mills are not recommended for use with HYDRAULIC
CHUCKS. Do not tighten the clamping screw without first
inserting a cutting tool into the tool holder. Always insert
the cutting tool into the hydraulic tool holder beyond min.
clamping length “E”.
2.6
2.9
5.3
— 5.7
-135 20mm 1.650
5.31 2.32 2.28-2.68 HDA20-16015 6.8
-165 6.50 1.69-2.68 HDA25-16039 7.9
-HDC25-110 25mm 2.240 2.48
2.05
7.3
-HDC32-110 32mm 2.520 2.95
4.33 2.44 3.07
—
2.20 12,000 8.2
A.3 HSK
PERFECT SEAL/
JET COLLET
PG. 361
187