BIG KAISER High Performance Tooling Solutions 2018-2019

øD1
øD
øD2
øD1
HYDRAULIC CHUCK
A.1
CLAMPING RANGE: ø.250"-1.250" (ø32mm)
For Drills, Reamers, Ball Mills, End Mills, Diamond Reamers & Grinding Tools
S P I N D L E S Y S T E M
DUAL CONTACT
R
COOLANT
BCV/CV
THROUGH
Adjusting Screw
(Optional)
H
E
Adjusting Screw
(Optional)
H
E
Adjusting Screw
(Optional)
H
E
ød
øD
øD1
ød
ød
øD
L1
L1
Fig. 1 Fig. 2
Fig. 3
L2
L
L
L1
L
Catalog
Number
Fig. ød øD øD1 øD2 L L1 L2 H
Min Clamping
Length E
Adjusting
Screw
Weight
(lbs.)
BCV50-HDC.250-3.5 1
— 3.50
—
7.3
-5
.250 1.024 2.750 1.53 5.00 1.75 3.19 1.10-1.97 1.10 HDA6-05032 8.0
2
-6.5 2.13 6.50 4.92 9.1
-HDC.375-3.5 1
— 3.50
—
7.3
-5
.375 1.181 2.750 1.71 5.00 1.75 3.27 1.30-2.17 1.30 HDA10-08032 8.0
2
-6.5 2.31 6.50 4.96 9.3
-HDC.500-3.5 1
— 3.50
—
7.6
-5
.500 1.299 2.750 1.85 5.00 1.75 3.31 1.50-2.36 1.50 HDA12-10032 8.2
2
-6.5 2.45 6.50 5.00 9.6
-HDC.625-3.5 1
— 3.50 1.75 —
7.8
-5
.625 1.496 2.750 1.97 5.00
3.35 1.69-2.76 1.69 HDA16-12037 8.7
2
2.00
-6.5 2.57 6.50 — 10.2
-HDC.750-3.5 1
— 3.50 1.75 3.43
8.0
-5
.750 1.654 2.750 2.15 5.00
5.04 1.69-2.76 1.69 HDA16-12037 8.9
2
2.00
-6.5 2.75 6.50 5.12 10.7
-HDC1.000-3.5
3.50 2.03
8.9
-5 3 1.000 2.480 2.750 — 5.00 3.54 — 2.05-3.15 2.05 HDA25-16039 10.7
-6.5 6.50 5.04 12.7
-HDC1.250-3.5
3.50 2.09
10.6
-5 3 1.250 2.717 2.750 — 5.00 3.58 — 2.20-3.15 2.20 HDA25-16039 11.8
-6.5 6.50 5.08 14.4
-HDC32-90 3 32mm 2.677 2.953 — 3.54 2.13 — 2.20-3.15 2.20 HDA25-16039 9.6
• “H” indicates the adjustment length with an adjusting screw
ACCESSORIES
PERFECT SEAL/
JET COLLET
PG. 361
CAUTION
!
Use only cutting tools that have a shank tolerance of h6 (see table Pg. 26). Do not use
with cutting tools made with a flat on the shank (ie: Weldon type shank). Roughing
end mills are not recommended for use with HYDRAULIC CHUCKs. Do not tighten
the clamping screw without first inserting a cutting tool into the tool holder. Always
insert the cutting tool into the hydraulic tool holder beyond min. clamping length “E”.
70