BIG KAISER High Performance Tooling Solutions 2018-2019

ROUGH BORING HEADS
SERIES 319 SW CHAMFERING INSERT HOLDERS
These insert holders are made for front and back chamfering on the twin cutter roughing heads Series 319 SW41-SW148
and cover the diameter range ø1.299"-8.268". The desired chamfering angle is adjustable from 15º-75º. The set contains
one insert holder and one blank piece.
L
D Min
D Max
Boring
Head
Catalog
Number
Reference
Number
Insert 15º 30º 45º 60º 75º
SW41 IH1SW41CF 10.639.104
1.850-2.362 1.929-2.441 1.968-2.480 1.968-2.480 1.929-2.441
SW53 IH1SW53CF 10.639.105 SC..09 2.323-2.992 2.402-3.071 2.441-3.110 2.441-3.110 2.402-3.071
SW68 IH1SW68CF 10.639.106 2.953-3.819 3.032-3.898 3.071-3.937 3.071-3.937 3.032-3.898
IH1SW98CF 10.639.107
3.858-4.961 3.936-5.039 3.976-5.079 3.936-5.039 3.897-5.000
SW98
IH2SW98CF 10.639.108 4.921-6.024 4.999-6.102 5.039-6.142 4.999-6.102 4.960-6.063
SC..12
IH1SW148CF 10.639.109 5.984-7.087 6.062-7.165 6.102-7.205 6.062-7.165 6.023-7.126
SW148
IH2SW148CF 10.639.110 7.047-8.150 7.125-8.228 7.165-8.268 7.125-8.228 7.086-8.189
*Insert holder must be mounted on RSS/BALANCED side of boring head
RADIAL CHAMFER LENGTH FOR FRONT (F1) AND BACK (F2) CHAMFERING
Applicable for inserts with .016" nose radius.
F2
15º
F1
F2
45º
F1
F2
75º
F1
Head
Type
SW41
SW53
SW68
SW98
SW148
Insert
15º 30º 45º 60º 75º
F1 F2 F1 F2 F1 F2 F1 F2 F1 F2
SC..09 .303 .028 .272 .055 .224 .071 .157 .067 .083 .047
SC..12 .417 .047 .374 .087 .307 .102 .217 .098 .110 .071
B.1 ROUGH BORING
SPARE PARTS
4
1
Head
Type
Torque
(ft-lbs.)
2 3
1 Pocket 2 Screw 3 Wrench Insert 4 Pin
SW41 10.695.101 10.691.756 10.690.899
10.694.138
SW53 10.695.101 10.691.756 10.690.899 SC..09 10.694.138
2.2
SW68 10.695.101 10.691.755 10.690.899 10.694.138
SW98
SW148
10.695.102 10.691.757 10.690.804
10.694.145
10.695.102 10.691.757 10.690.804 10.694.145
SC..12
10.695.102 10.691.757 10.690.804 10.694.145
10.695.102 10.691.757 10.690.804 10.694.145
2.2
401