BIG KAISER High Performance Tooling Solutions 2018-2019

HYDRAULIC CHUCKS
Catalog
Number
Fig. ød øD øD1 L L1 L2 H
Min Clamping
Length E
Adjusting
Screw
Weight
(lbs.)
BBT40-HDC6-60 1
1.063
2.36 .75 —
2.7
-90
3.54
1.97 3.0
-110 6mm
1.77 4.33 2.76 1.10-1.97 1.10 HDA6-05032 3.3
2 1.024
1.73
-135 5.31 3.74 3.6
-165 6.50 4.69 4.2
-HDC8-60 1
1.142
2.36 .75 —
2.7
-90
3.54
1.97 3.0
-110 8mm
1.77 4.33 2.76 1.10-1.97 1.10 HDA8-06032 3.3
2 1.102
1.73
-135 5.31 3.74 3.8
-165 6.50 4.69 4.3
-HDC10-60 1
1.220
2.36 .79 —
2.7
-90
3.54
1.97 3.0
-110 10mm
1.77 4.33 2.76 1.30-2.17 1.30 HDA10-08032 3.3
2 1.181
1.77
-135 5.31 3.74 3.8
-165 6.50 4.69 4.3
-HDC12-60 1
1.299
2.36 .79 —
2.7
-90
3.54
1.93 3.0
-110 12mm
1.77 4.33 2.72 1.50-2.36 1.50 HDA12-10032 3.4
2 1.260
1.77
-135 5.31 3.70 3.9
-165 6.50 4.69 4.3
-HDC14-90
3.54
1.93
3.0
-110 2 14mm 1.339 1.77 4.33 1.81 2.72 1.50-2.36 1.50 HDA12-10032 3.4
-135 5.31 3.70 3.9
-HDC16-75
2.95 1.38 1.42
2.9
-90 3.54
1.93 3.1
1.77
-110 2 16mm 1.496
4.33 2.72 1.70-2.76 1.70 HDA16-16037 3.5
1.85
-135 5.31 3.70 4.1
-165 1.97 6.50 4.69 5.1
-HDC18-90
3.54
1.93
3.2
-110 2 18mm 1.575 1.77 4.33 1.89 2.72 1.70-2.76 1.70 HDA16-12037 3.5
-135 5.31 3.70 4.1
-HDC20-90
1.77 3.54
1.97
3.1
-110
4.33 2.76 3.8
2 20mm 1.654
1.89
1.70-2.76 1.70 HDA16-12037
-135 1.97 5.31 3.74 4.3
-165 6.50 4.69 5.2
A.2 BBT/BT
• In case the projection length needs to be adjusted from the shank side, add the letter “W” to adjusting screw model number for hexagon sockets on both sides
ACCESSORIES
PERFECT SEAL/
JET COLLET
PG. 361
CAUTION
!
Use only cutting tools that have a shank tolerance of h6 (see table Pg. 26). Do not use with cutting tools made with a flat on the
shank (ie: Weldon type shank). Roughing end mills are not recommended for use with HYDRAULIC CHUCKS. Do not tighten the
clamping screw without first inserting a cutting tool into the tool holder. Always insert the cutting tool into the hydraulic tool
holder beyond min. clamping length “E”.
129