ICAM Virtual Machine V19 - Kxcad.net

More documents

Recommendations

Info

ICAM Virtual Machine ® Virtual Machine Reference, Model Customization Simulation Macro Variables, Error Message Variables 4.4.6.9 Error Message Variables $ERRMSG Error message on indicator Type: Logical, Read/Write This variable indicates if error messages are to be output or not. Error messages may be disabled by setting $ERRMSG to $FALSE. Set $ERRMSG to $TRUE to once again enable error message output. Error message output is enabled by default at the start of processing. $ERRNO Last I/O status Type: Numeric, Read-only I/O status code returned by the system following the last SYSTEM, OPEN, READ, WRITE or CLOSE command. I/O status codes are system specific, but most systems use a status of zero for success, negative for warning (like end-of-file) and positive for errors. $ERR08 Number of error diagnostics Type: Numeric, Read/Write Current number of diagnostics at severity levels 8 through 15. $FTL16 Number of fatal error diagnostics Type: Numeric, Read/Write Current number of diagnostics at severity level 16 or higher. $MSG00 Number of informational diagnostics Type: Numeric, Read/Write Current number of diagnostics at severity levels 0 through 3. $WRN04 Number of warning diagnostics Type: Numeric, Read/Write Current number of diagnostics at severity levels 4 through 7. 216 ICAM Technologies Corporation – Proprietary
4.4.6.10 Miscellaneous Variables $BACK Background processing flag Type: Logical, Read-only Virtual Machine Reference, Model Customization Simulation Macro Variables, Miscellaneous Variables This variable will be set $TRUE if the -back UNIX /back Windows command line qualifier was specified when the CERUN or GENER application was started. The purpose of this variable is to advise macros that the process is running in a state where user interaction is not possible (e.g., as a UNIX background process). It is the responsibility of the model writer to test this variable before calling the $FDIALOG function or performing I/O to the STDIN and STDOUT devices. $DATE Current date and time Type: String, Read-only This variable contains the current date and time. The character string returned by $DATE is formatted as “dd-mmm-yyyy hh:mm:ss.ss”. $PARAM Current date and time Type: String, Read-only This variable contains the command line that initiated CERUN or GENER. It will list all of the run time options selected by the user at the start of processing. See $UPARAM (below) for information concerning user defined parameters. $PLEV Product level Type: Numeric, Read-only This variable contains the release level number of Virtual Machine, as a whole number in the form “yyww”: where “yy” are the last two digits of the year, and “ww” is the week number of the year in the range 01-52. $PVER Product version Type: Numeric, Read-only This variable contains the release version number of Virtual Machine (e.g., 19 for V19). $UPARAM CERUN or GENER user defined command line parameters Type: String, Read/Write The $UPARAM macro system variable is similar to the $PARAM macro system variable. $UPARAM is a string containing the user defined parameters from the CERUN or GENER command line following the -u UNIX or /u Windows options. The $PARAM string on the other hand lists all command line parameters, including the user defined ones. See the $FARGC and $FARGV functions for information on how to extract general and user defined parameters. ICAM Technologies Corporation – Proprietary 217
Page 1 and 2:
ICAM Technologies Corporation Virtu
Page 3 and 4:
Welcome Welcome ICAM Virtual Machin
Page 5 and 6:
Table of Contents Table of Contents
Page 7 and 8:
Table of Contents 4.4.2.1 The Model
Page 9 and 10:
1 Overview ICAM Virtual Machine ®
Page 11 and 12:
Overview order to avoid false colli
Page 13 and 14:
Using Virtual Machine Models with C
Page 15 and 16:
Database: Using Virtual Machine Mod
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
2.4 Navigating the Simulation Windo
Page 23 and 24:
Camera Roll: Using Virtual Machine
Page 25 and 26:
2.5 Adjusting Lighting Using Virtua
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
2.7 Setting Fixture Compensation Us
Page 33 and 34:
2.8.1 Lathe Tool Definition Select
Page 35 and 36:
2.8.3 Holder Definition A holder ca
Page 37 and 38:
2.9 Setting Tool Compensation Using
Page 39 and 40:
2.10.1 Head-Up Display Using Virtua
Page 41 and 42:
2.10.4 VM Controller Timeline Using
Page 43 and 44:
3 Creating Virtual Machine Models w
Page 45 and 46:
Creating Virtual Machine Models wit
Page 47 and 48:
3.3 Creating a Virtual Machine Mode
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Step 1: Create the base Creating Vi
Page 57 and 58:
3.6 Collision Testing The model as
Page 59 and 60:
Page 61 and 62:
3.7 Selection Groups Selection grou
Page 63 and 64:
3.9 Testing the Model Creating Virt
Page 65 and 66:
4 Virtual Machine Reference Virtual
Page 67 and 68:
Virtual Machine Reference Table of
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
4.1 Input Controls 4.1.1 Standard K
Page 75 and 76:
4.2 Toolbar Virtual Machine Referen
Page 77 and 78:
Virtual Machine Reference, Toolbar
Page 79 and 80:
4.2.5 VM View Virtual Machine Refer
Page 81 and 82:
4.2.8 VM Measure (CERUN & GENER onl
Page 83 and 84:
Virtual Machine Reference, Menu Bar
Page 85 and 86:
Page 87 and 88:
Within VM, objects are constructed
Page 89 and 90:
Page 91 and 92:
Lathe Tool Type Select “Lathe”
Page 93 and 94:
Mill Tool Type Select “Mill” as
Page 95 and 96:
Holders Virtual Machine Reference,
Page 97 and 98:
Generic Holder Type Select “Gener
Page 99 and 100:
4.3.6 Simulation»Construct Entity
Page 101 and 102:
Simulation»Construct Entity»Spher
Page 103 and 104:
Simulation»Construct Entity»Pictu
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
4.3.8 Simulation»Camera Controls v
Page 113 and 114:
Simulation»Camera»View Angle (Shi
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
4.3.11 Simulation»Use World CS (QU
Page 121 and 122:
4.3.16 Simulation»Grid (Ctrl Alt G
Page 123 and 124:
4.3.18 Simulation»Materials (Ctrl
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
4.3.22 Simulation»Open Setup (CERU
Page 131 and 132:
4.4.1 The Macro Language Virtual Ma
Page 133 and 134:
Virtual Machine Reference, Model Cu
Page 135 and 136:
Detecting Data Type Mismatching Vir
Page 137 and 138:
Operators Numeric, String and Seque
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
It is good programming practice to
Page 147 and 148:
4.4.1.6 String Format Specification
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
4.4.2 Model Startup/Shutdown Macros
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
4.4.5.2 Mathematical Functions $FAC
Page 163 and 164:
4.4.5.3 Numerical Functions $FABS A
Page 165 and 166:
4.4.5.4 Geometric Functions $FGLNXP
Page 167 and 168:
4.4.5.5 Vector Functions $FVADD Vec
Page 169 and 170:
The $FVROTN Function result=$FVROTN
Page 171 and 172:
The $FMXINV Function result=$FMXINV
Page 173 and 174: esult=$FMAJOR(string) Returns: Reco
Page 175 and 176: The $FISNUM Function result=$FISNUM
Page 177 and 178: 4.4.5.9 Character and Sequence Func
Page 179 and 180: Virtual Machine Reference, Model Cu
Page 181 and 182: The $FSEQ Function result=$FSEQ([a1
Page 183 and 184: 4.4.5.10 Command Line Functions $FA
Page 185 and 186: The $FBASNAM Function result=$FBASN
Page 187 and 188: The following values are supported
Page 189 and 190: The $FMSADPT Function result=$FMSAD
Page 193 and 194: Head Component ID result=$FMSID(HEA
Page 195 and 196: The $FMSLCS Function result=$FMSLCS
Page 199 and 200: 4.4.5.13 Virtual Machine Channel Fu
Page 203 and 204: The $FMSCEZ Function result=$FMSCEZ
Page 205 and 206: The $FMSPDAT Function result=$FMSPD
Page 209 and 210: 4.4.5.15 Other Functions $FDIALOG A
Page 213 and 214: 4.4.6 Simulation Macro Variables Vi
Page 215 and 216: 4.4.6.3 Virtual Machine Variables $
Page 217 and 218: 4.4.6.4 Machine & Workpiece Coordin
Page 221 and 222: 4.4.6.6 Cutter Compensation Variabl
Page 223: 4.4.6.8 MCD/Tape Variables $LMCD La
Page 227 and 228: $ $ macro continuation, 124 $$ macr
Page 229 and 230: Collision avoidance, 1, 10, 181 det
Page 231 and 232: G $FVNORM, 160 $FVROTN, 161 $FVSUB,
Page 233: STL, 1, 2, 3, 18, 25, 27, 38, 46, 6
show all

ICAM Virtual Machine V19 - Kxcad.net

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?