Defensor Mk5 Technical Documentation

More documents

Recommendations

Info

4.4.2 Accessory details Steam distribution pipes 81-... for indirect room humidification The steam distribution pipes are selected on the basis of the duct width (for horizontal installation) or the duct height (for vertical installation) and the capacity of the steam humidifier. Important! Always select the longest possible steam distribution pipe (optimum humidification distance). L B Steam distribution pipes 81-... for Defensor Mk5 (CrNi steel) Duct width (B) Steam output Type Length in mm (L) 3) in mm max. in kg/h 81-200 1) 200 210…400 10 81-350 2) 350 400…600 30 81-500 2) 500 600…750 30 81-650 650 750…900 50 81-800 800 900…1100 50 81-1000 1000 1100…1300 50 81-1200 1200 1300…1600 50 81-1500 1500 1600…2000 50 81-1800 1800 2000…2400 50 81-2000 2000 2200…2600 50 81-2300 2300 2500…2900 50 81-2500 2500 2700…3100 50 1) Only for units with a max. steam capacity of 10 kg/h 2) Only for units with a max. steam capacity of 30 kg/h 3) Special length available on request Note: If the humidification distance (see chapter 5.3.1) has to be reduced for technical reasons, the amount of steam per basic unit must be divided between two steam distribution pipes or the OptiSorp steam distribution system must be used. If this is the case, contact your Defensor supplier. Steam distribution pipe “Process” (accessory “Z...”) The steam distribution pipe “Process” is used for direct humidification of material in manufacturing processes (process humidification), or in ventilation ducts with a critical saturation distance (the steam distribution pipe “Process” reduces the saturation distance by approximately 30%). The desired length must be specified when ordering. Please contact your Defensor distributor, they will assist you in customizing the steam distribution head “Process”. Please have the following information readily available: – steam quantity in kg/h – dimensions of ventilation duct (width x height) Important! The table for the determination of the humidification distance provided in chapter 5.3.1 does not apply to the Process steam distribution pipe. 17
18 OptiSorp steam distribution system The OptiSorp steam distribution system is used in ventilation ducts where only a short humidification distance is available (see chapter 5.3.1 for calculation of humidification distance). Duct dimensions should be given when ordering. Please note the following data for this: H B OptiSorp Number of max. steam capacity Duct dimension steam connections in kg/h 1) Width in mm Height in mm System 1 1 45 (30) 450...2700 450...1650 System 2 2 90 (60) 450...2700 450...2200 1) For duct width
Page 1 and 2: 1115661 EN neutral 0407 Steam humid
Page 4 and 5: Contents 1 Introduction 4 1.1 To th
Page 6 and 7: 2 For your safety Intended use Stea
Page 8 and 9: The type designation is structured
Page 10 and 11: 3.5 Functional description The Defe
Page 12 and 13: 3. Calculating the maximum required
Page 14 and 15: 4.2 Selecting the control system Th
Page 16 and 17: 4.3 Options The following table pre
Page 20 and 21: 4.5 Additional planning instruction
Page 22 and 23: Minimum distances to observe min. 6
Page 24 and 25: 5.3 Steam installation 5.3.1 Positi
Page 26 and 27: 3/7 2/7 2/7 2/5 1/5 1/5 1/5 2/6 1/6
Page 28 and 29: 5.3.3 Installing the steam hose Imp
Page 30 and 31: - Steam distribution pipe is mounte
Page 32 and 33: Water supply The water feed pipe (m
Page 34 and 35: 5.5 Electric installation Up Uc 1 2
Page 36 and 37: Legend to wiring diagram A1 Control
Page 38 and 39: Control voltage supply Uc Caution!
Page 40 and 41: 5.5.4 Inspecting the electrical ins
Page 42 and 43: Setting the maintenance interval (
Page 44 and 45: Remote operating and fault indicati
Page 46 and 47: Description of the operating parame
Page 48 and 49: inlet valve cor. 100 serial interfa
Page 50 and 51: Call-up of the setting level Mk5 Vi
Page 52 and 53: Integr.time[min] 010 softstart off
Page 54 and 55: 6.6 Maintenance 6.6.1 Notes on main
Page 56 and 57: Removal and dismantling of the stea
Page 58 and 59: 6.6.3 Notes on cleaning Cleaning th
Page 60 and 61: 6.7.2 What, if..? Most operational
Page 62 and 63: 6.7.3 Replacing unit fuses Warning
Page 64 and 65: © Axair Ltd. 2000, Printed in Swit

Defensor Mk5 Technical Documentation

Create successful ePaper yourself

Delete template?

Save as template?