Defensor Mk5 Technical Documentation

More documents

Recommendations

Info

inlet valve cor. 100 serial interface on baudrate 2400 RTS/CTS off analog signal 0 - 5V (poti) software version V 1.00 machine type 20kg/400V – Inlet valve correction Set inlet valve correction (cycle ratio) in % of standard setting value to balance out water pressure variations. Note: This menu point is available only with Mk5 Process units. – Serial interface Serial interface (option) activated (“on”)/deactivated (“off”). – Data transfer rate Selected data transfer rate (baud rate). Note: This menu option is available only if the serial interface is active. – Data flow control Transmission with (“on”) or without (“off”) RTS/CTS data flow control. Note: This menu option is available only if the serial interface is active. – Analog signal Range of the active analog signal in V or mA, respectively. Note: The range of the analog signal may be adjusted using the rotary switch “S3” on the control board. Please observe the information given in chapter 6.1. – Software version Current software version for the steam humidifier. – Unit type value left: Max. steam capacity in kg/h value right: Heating voltage in VAC 47
6.5 Setting the operating parameters 48 You can adapt various Defensor Mk5 steam-air humidifier operating parameters to the operating requirements on the setting level of the control and display unit. The setting level is protected by an access code to guard against unauthorized access. Caution! The settings on the setting level have a direct influence on the operating behavior of the steam-air humidifier. The settings must therefore only be made by personnel who are familiar with the techniques of humidification and climatic control and with the Defensor Mk5 system. Overview of the setting level and operation Mk5 Visual ready and entry code 8808 adjust level language (Enter=Entry) power limit [%] (Enter=Entry) 1) inlet valve cor. (Enter=Entry) controller funct (Enter=Entry) 2) ref.value rh[%] (Enter=Entry) 2) P-band [%] (Enter=Entry) 2) integr.time[min] (Enter=Entry) Operation: – For call-up of the setting level see the following “Call-up of the setting level” – Next menu item – Previous menu item – For change to set values see the section “Changing the set values” – Exit the setting level with Note: 1) appears only on Mk5 Process units 2) appears only if “controller funct” is activate (“on”) 3) appears only if “softstart” is activate (“on”) 4) appears only if “demineral. mode” is activate (“on”) 5) appears only if “serial interface” is activate (“on”) Menu softstart (Enter=Entry) 3) softstart time (Enter=Entry) 3) softst. power (Enter=Entry) demineral. mode (Enter=Entry) 4) demineral. delay (Enter=Entry) Normal service mode Setting level serial interface (Enter=Entry) 5) baudrate (Enter=Entry) 5) RTS/CTS (Enter=Entry) diagnose pgm (Enter=Entry) faulthistory . /. /6.B/6.A erase history (Enter=Entry)
Page 1 and 2: 1115661 EN neutral 0407 Steam humid
Page 4 and 5: Contents 1 Introduction 4 1.1 To th
Page 6 and 7: 2 For your safety Intended use Stea
Page 8 and 9: The type designation is structured
Page 10 and 11: 3.5 Functional description The Defe
Page 12 and 13: 3. Calculating the maximum required
Page 14 and 15: 4.2 Selecting the control system Th
Page 16 and 17: 4.3 Options The following table pre
Page 18 and 19: 4.4.2 Accessory details Steam distr
Page 20 and 21: 4.5 Additional planning instruction
Page 22 and 23: Minimum distances to observe min. 6
Page 24 and 25: 5.3 Steam installation 5.3.1 Positi
Page 26 and 27: 3/7 2/7 2/7 2/5 1/5 1/5 1/5 2/6 1/6
Page 28 and 29: 5.3.3 Installing the steam hose Imp
Page 30 and 31: - Steam distribution pipe is mounte
Page 32 and 33: Water supply The water feed pipe (m
Page 34 and 35: 5.5 Electric installation Up Uc 1 2
Page 36 and 37: Legend to wiring diagram A1 Control
Page 38 and 39: Control voltage supply Uc Caution!
Page 40 and 41: 5.5.4 Inspecting the electrical ins
Page 42 and 43: Setting the maintenance interval (
Page 44 and 45: Remote operating and fault indicati
Page 46 and 47: Description of the operating parame
Page 50 and 51: Call-up of the setting level Mk5 Vi
Page 52 and 53: Integr.time[min] 010 softstart off
Page 54 and 55: 6.6 Maintenance 6.6.1 Notes on main
Page 56 and 57: Removal and dismantling of the stea
Page 58 and 59: 6.6.3 Notes on cleaning Cleaning th
Page 60 and 61: 6.7.2 What, if..? Most operational
Page 62 and 63: 6.7.3 Replacing unit fuses Warning
Page 64 and 65: © Axair Ltd. 2000, Printed in Swit

Defensor Mk5 Technical Documentation

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?