Ambient Air quality Monitoring Guidlines. - Maharashtra Pollution ...

More documents

Recommendations

Info

8.0 APPARATUS 8.1 Chemiluminescene Instrument - Two basic instrument designs has been developed for the measurement of total oxides of nitrogen, nitric oxide and the indirect determination of nitrogen dioxide. In both cases, the determination of NOx (NOx = NO + NO2) and NO must be accomplished and the nitrogen dioxide calculated by subtraction of NO from the NOx. The two instrument configurations utilize the cyclic or dual mode of operation. 8.1.1 The cyclic mode instrument is shown schematically in Figure-1, and has a single reaction chamber and detector. The incoming sample air is alternately cycled directly to the reaction chamber to determine NO, or through the instrument converter to determine NOx. A normal cycle, which is approximately thirty (30) seconds, is accomplished by means of a timer controlled solenoid valve. Separate NOx and NO values are determined every thirty seconds. The photomultiplier tube outputs are amplified and stored in memory circuits; the difference output, nitrogen dioxide, is updated electronically after each cycle and similarly stored. Reorder outputs are available for all three measurement channels, NO, NO2 and NOx. 8.1.2 The dual mode instrument is shown schematically in Figure-2, and has two reaction chambers and a single detector. The incoming air sample is split into two separate streams. The NO sample stream is routed directly to the reaction chamber, while the NOx sample stream first passes through the instrument converter before entering the second reaction chamber. An optical chopper alternately exposes the detector to the respective chemiluminescent outputs, generating continuous outputs for both NO and NOx. The outputs are amplified and stored in memory circuits; real-time NO2 data obtained by difference are continuously generated. Reorder outputs are available for the NO, NO2, and NOx concentration. 8.1.3 Converters - For the accurate determination of nitrogen dioxide it is essential that the instrument converters have a high degree of efficiency (95%+) for the conversion of NO2 to NO. The converters employed in commercially available instruments are of two basic types. 8.1.3.1 Thermal Converters are made of a high grade stainless steel and operate at elevated temperatures, 600-800 o C. At these temperatures the breakdown of NO2 into NO and O2 occurs readily. These converters, though adequate for the breakdown of NO2 to NO, have the obvious disadvantage of converting ammonia into NO (See Section 6). 8.1.3.2 Chemical converters are to be found in the majority of chemiluminescence instruments used for ambient monitoring. These converters have the advantage of a much lower operating temperature, 200-400 o C, with efficient NO2 conversion. Molybdenum and carbon converters have been in general use and are available in commercial instruments. 130
SAMPLE INLET PUMP AIR DRYER OZONE GENERATOR THREE WAY VALVE NO2 CONVERTER SCRUBBER ( O3 & NO2 ) FIG : 1 CYCLIC MODE CHEMILUMINESCENT ANALYZER. 131 REACTION CHAMBER PHOTOMULTIPLIER TUBE THERMOELECTRIC COOLER
Page 1 and 2:
1.0 INTRODUCTION Air pollutants are
Page 3 and 4:
The Central Pollution Control Board
Page 5 and 6:
S.No. Problem Area Type of Industry
Page 7 and 8:
(viii) High population exodus to th
Page 9 and 10:
a) Seasonal Variation in Carbon Mon
Page 11 and 12:
Concentration (µg/m 3 ) 2.2.3 Long
Page 13 and 14:
3.2 National Air Monitoring Program
Page 15 and 16:
Number of Monitoring Stations 40 35
Page 17 and 18:
4.0 GUIDELINES FOR MONITORING For s
Page 19 and 20:
The variability of pollutant concen
Page 21 and 22:
areas, traffic intersections etc. O
Page 23 and 24:
Station Type Description Type C Res
Page 25 and 26:
available then monitoring of specif
Page 27 and 28:
manpower and needs to be calibrated
Page 29 and 30:
averaging should be done and plotte
Page 31 and 32:
necessary to readjust the position
Page 33 and 34:
5.0 QUALITY ASSURANCE AND QUALITY C
Page 35 and 36:
(a) Inter Laboratory Proficiency Te
Page 37 and 38:
2. Infrastructure for conducting In
Page 39 and 40:
ZERO GAS VALVE PRESSURE REGULATOR (
Page 41 and 42:
is to assess its ability to perform
Page 43 and 44:
The mixing ratio of O3 (ppb) must n
Page 45 and 46:
(vi) Lack of Dedicated Manpower If
Page 47 and 48:
Site staff must be trained so that
Page 50 and 51:
NATIONAL AMBIENT AIR QUALITY MONITO
Page 52 and 53:
Delhi - 110 032 e-mail : cpcb@alpha
Page 54 and 55:
FOREWORD Under the Air (Prevention
Page 56 and 57:
Table No. References 161 LIST OF TA
Page 58 and 59:
3.0 INTRODUCTION Air pollutants are
Page 60 and 61:
The Central Pollution Control Board
Page 62 and 63:
S.No. Problem Area Type of Industry
Page 64 and 65:
(viii) High population exodus to th
Page 66 and 67:
Monthly average of CO measured at B
Page 68 and 69:
Concentration (µg/m 3 ) 2.2.3 Long
Page 70 and 71:
3.2 National Air Monitoring Program
Page 72 and 73:
Number of Monitoring Stations 40 35
Page 74 and 75:
4.0 GUIDELINES FOR MONITORING For s
Page 76 and 77:
The data requirements, which are re
Page 78 and 79:
their levels and determine trends.
Page 80 and 81:
Station Type Description traffic vo
Page 82 and 83:
Criteria for SO2 Measurements Sourc
Page 84 and 85:
calibration parameters change. Meas
Page 86 and 87:
The following must be followed for
Page 88 and 89:
changed in inclement weather. Set t
Page 90 and 91:
5.0 QUALITY ASSURANCE AND QUALITY C
Page 92 and 93:
(a) Inter Laboratory Proficiency Te
Page 94 and 95:
The primary requirement for conduct
Page 96 and 97:
ZERO GAS VALVE PRESSURE REGULATOR (
Page 98 and 99:
is to assess its ability to perform
Page 100 and 101:
The mixing ratio of O3 (ppb) must n
Page 102 and 103:
(xiii) Lack of Dedicated Manpower I
Page 104 and 105:
laboratory staff must be trained so
Page 106 and 107:
1. AIR SAMPLING - GASEOUS 1.0 TITLE
Page 108 and 109:
52 Fig. 1 Sampling Train
Page 110 and 111:
54 Fig. 4 Critical Orifice Device
Page 112 and 113:
the pollutant and accordingly selec
Page 114 and 115:
contracts with change in humidity.
Page 116 and 117:
and temperature has been set down i
Page 118 and 119:
The impulse frequency emitted is pr
Page 120 and 121:
CIRCUIT DIAGRAM - 1 64
Page 122 and 123:
FIG. 1 (a) CIRCUIT DIAGRAM 66
Page 124 and 125:
3. DETERMINATION OF SUSPENDED PARTI
Page 126 and 127:
measurement precision dominates at
Page 128 and 129:
6.4.4 Equilibration Rack - This rac
Page 130 and 131:
Receive Filters, inspect (light tab
Page 132 and 133:
of the face-plate. Look underneath
Page 134 and 135:
Atmosphere". Federal Register, 52 F
Page 136 and 137:
5.0 INTERFERENCES 5.1 Passive Depos
Page 138 and 139: 6.4.4 Numbering Machine - Though fi
Page 140 and 141: chain-of-the custody log-book and o
Page 142 and 143: 5. DETERMINATION OF SULPHUR DIOXIDE
Page 144 and 145: 88 FIG. 1.0 SO2 SAMPLING TRAIN
Page 146 and 147: The wavelength calibration of the i
Page 148 and 149: (ii) The absorbance of the reagent
Page 150 and 151: pipe cleaner after use. If, the tem
Page 152 and 153: (A - Ao) (10 3 ) (B) C = ----------
Page 154 and 155: Then the air sample flows into a re
Page 156 and 157: integral part of the apparatus, or
Page 158 and 159: 6.4 Pressure Regulator The output s
Page 160 and 161: FIG. 2 SCHEMATIC DIAGRAM OF A CALIB
Page 162 and 163: 7. CONTINUOUS MEASUREMENT OF CARBON
Page 164 and 165: 6.0 APPARATUS 6.1 NDIR Analyser - f
Page 166 and 167: BLOWER SAMPLE INLET PORT FOUR WAY V
Page 168 and 169: Maintain the same sample cell flow
Page 170 and 171: 14.0 CALIBRATION PROCEDURE 14.1 Ana
Page 172 and 173: connected to the output manifold, t
Page 174 and 175: FIG. 3 MULTIPLE CYLINDER CALIBRATIO
Page 176 and 177: (Nondispersive Infrared Spectrometr
Page 178 and 179: 5.0 INTERFERENCES 5.1 Nitric oxide
Page 180 and 181: 7.1.6 Air Pump - Capable of maintai
Page 182 and 183: 9.1.3.2 Solution B - Pipet 25 ml of
Page 184 and 185: 9.4.7 A randomly selected 5-10% of
Page 186 and 187: 9. CONTINUOUS MEASUREMENT OF OXIDES
Page 190 and 191: SAMPLE INLET PUMP AIR DRYER OZONE G
Page 192 and 193: FIG. 3 CALIBRATION SYSTEM COMPONENT
Page 194 and 195: 10.3.1 Flow Conditions - Insure tha
Page 196 and 197: ates constant. For each calibration
Page 198 and 199: 10. DETERMINATION OF OZONE IN THE A
Page 200 and 201: 7.0 APPARATUS 7.1 Sampling Probe -
Page 202 and 203: 9.4 Blank Correction - Measure the
Page 204 and 205: 11. CONTINUOUS MEASUREMENT OF OZONE
Page 206 and 207: FIG. 1 SCHEMATIC DIAGRAM OF A TYPIC
Page 208 and 209: 8.2 Air Inlet Filter - A Teflon fil
Page 210 and 211: 9.0 REAGENTS 9.1 Purity - All reage
Page 212 and 213: Where : Ozone Conc.CTA = the ozone
Page 214 and 215: 1. AIR SAMPLING - GASEOUS 1.0 TITLE
Page 216 and 217: 55 Fig. 1 Sampling Train
Page 218 and 219: 57 Fig. 4 Critical Orifice Device
Page 220 and 221: the pollutant and accordingly selec
Page 222 and 223: (iii) Technical Data Measuring rang
Page 224 and 225: 3.1.3 Wind Speed Temperature measur
Page 226 and 227: (v) Preparation for Use (a) Selecti
Page 228 and 229: CIRCUIT DIAGRAM - 1 67
Page 230 and 231: FIG. 1 (a) CIRCUIT DIAGRAM 69
Page 232 and 233: 3. DETERMINATION OF SUSPENDED PARTI
Page 234 and 235: measurement precision dominates at
Page 236 and 237: 6.4.4 Equilibration Rack - This rac
Page 238 and 239:
Receive Filters, inspect (light tab
Page 240 and 241:
of the face-plate. Look underneath
Page 242 and 243:
Atmosphere". Federal Register, 52 F
Page 244 and 245:
5.0 INTERFERENCES 5.1 Passive Depos
Page 246 and 247:
6.4.4 Numbering Machine - Though fi
Page 248 and 249:
chain-of-the custody log-book and o
Page 250 and 251:
5. DETERMINATION OF SULPHUR DIOXIDE
Page 252 and 253:
91 FIG. 1.0 SO2 SAMPLING TRAIN
Page 254 and 255:
The wavelength calibration of the i
Page 256 and 257:
(ii) The absorbance of the reagent
Page 258 and 259:
pipe cleaner after use. If, the tem
Page 260 and 261:
(A - Ao) (10 3 ) (B) C = ----------
Page 262 and 263:
Then the air sample flows into a re
Page 264 and 265:
integral part of the apparatus, or
Page 266 and 267:
6.4 Pressure Regulator The output s
Page 268 and 269:
FIG. 2 SCHEMATIC DIAGRAM OF A CALIB
Page 270 and 271:
7. CONTINUOUS MEASUREMENT OF CARBON
Page 272 and 273:
6.0 APPARATUS 6.2 NDIR Analyser - f
Page 274 and 275:
BLOWER SAMPLE INLET PORT FOUR WAY V
Page 276 and 277:
Maintain the same sample cell flow
Page 278 and 279:
14.0 CALIBRATION PROCEDURE 14.1 Ana
Page 280 and 281:
connected to the output manifold, t
Page 282 and 283:
FIG. 3 MULTIPLE CYLINDER CALIBRATIO
Page 284 and 285:
(Nondispersive Infrared Spectrometr
Page 286 and 287:
5.0 INTERFERENCES 5.1 Nitric oxide
Page 288 and 289:
7.1.6 Air Pump - Capable of maintai
Page 290 and 291:
9.1.3.2 Solution B - Pipet 25 ml of
Page 292 and 293:
9.4.7 A randomly selected 5-10% of
Page 294 and 295:
9. CONTINUOUS MEASUREMENT OF OXIDES
Page 296 and 297:
9.0 APPARATUS 8.1 Chemiluminescene
Page 298 and 299:
SAMPLE INLET PUMP AIR DRYER OZONE G
Page 300 and 301:
FIG. 3 CALIBRATION SYSTEM COMPONENT
Page 302 and 303:
10.6.1 Flow Conditions - Insure tha
Page 304 and 305:
ates constant. For each calibration
Page 306 and 307:
10. DETERMINATION OF OZONE IN THE A
Page 308 and 309:
7.0 APPARATUS 7.1 Sampling Probe -
Page 310 and 311:
9.4 Blank Correction - Measure the
Page 312 and 313:
11. CONTINUOUS MEASUREMENT OF OZONE
Page 314 and 315:
FIG. 1 SCHEMATIC DIAGRAM OF A TYPIC
Page 316 and 317:
8.2 Air Inlet Filter - A Teflon fil
Page 318 and 319:
9.0 REAGENTS 9.3 Purity - All reage
Page 320 and 321:
Where : Ozone Conc.CTA = the ozone
show all

Ambient Air quality Monitoring Guidlines. - Maharashtra Pollution ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?