ECL Comfort 210/310, A217/A317 Installation Guide - Danfoss ...

More documents

Recommendations

Info

Installation Guide ECL Comfort 210 / 310, application A217 / A317 Ext. reset 2151 Circuit Setting range Factory setting This setting is only used in connection with set-up of Modbus communication. 0: Reset not activated. 1: Reset. 6.8.10 Language 0 / 1 0 Language 2050 Circuit Setting range Factory setting Choose your language. English / ‘Local’ English Local language is selected during installation. If you want to change to another local language, the application must be reinstalled. However, it is always possible to change between the local language and English. 104 DEN-SMT/DK VI.LG.U2.02 Danfoss District Energy
Installation Guide ECL Comfort 210 / 310, application A217 / A317 7.0 Miscellaneous 7.1 Several controllers in the same system When ECL Comfort controllers are interconnected by means of the ECL 485 communication bus (cable type: 2 x twisted pair), the master controller will broadcast the following signals to the slave controllers: • Outdoor temperature (measured by S1) • Time and date • DHW heating activity Furthermore, the master controller can receive information about the desired flow temperature (demand) from slave controllers. SLAVE controllers: How to make use of the outdoor temperature signal sent from the MASTER controller Situation 1: The slave controllers only receive information about outdoor temperature and date / time. SLAVE controllers: Change the factory set address from 15 to address 0. • In , go to System > Communication > ECL 485 addr: ECL 485 addr. (master / slave address) 2048 Circuit Setting range Choose 0 ... 15 0 SLAVE controller: How to react on a DHW heating demand sent from the MASTER controller Situation 2: The slave receives information about a DHW heating activity in the master controller and can be set to close the selected heating circuit. SLAVE controller: Set the desired function: • In circuit 1 / circuit 2, go to ‘Settings’ > ‘Application’ >’DHW priority’: DHW priority (closed valve / normal operation) 11052 / 12052 Circuit Setting range Choose 1 / 2 OFF / ON OFF / ON OFF: The flow temperature control remains unchanged during active DHW heating / charging in the master controller. ON: The valve in the heating circuit is closed during active DHW heating / charging in the master controller. In a system with MASTER / SLAVE controllers, only one MASTER controller with address 15 is allowed. If by mistake more MASTER controllers are present in an ECL 485 communication bus system, decide which controller is to be MASTER. Change the address in the remaining controllers. However, the system will operate but not be stable with more than one MASTER controller. In the MASTER controller, the address in ‘ECL 485 addr. (master / slave address)’, ID no. 2048, must always be 15. Danfoss District Energy VI.LG.U2.02 DEN-SMT/DK 105
Page 1 and 2:
Installation Guide ECL Comfort 210
Page 3 and 4:
Page 5 and 6:
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54: Installation Guide ECL Comfort 210
Page 103: Installation Guide ECL Comfort 210
Page 113: Installation Guide ECL Comfort 210
show all

ECL Comfort 210/310, A217/A317 Installation Guide - Danfoss ...

Create successful ePaper yourself

Delete template?

Save as template?