INSTRUCTION MANUAL - Scorpio

More documents

Recommendations

Info

MODEL NAME/USER NAME: MODEL NAME assigns a name to the current model memory. By giving each model a name that is immediately recognizable, a crash. USER NAME Adjustability and values: MODEL NAME: format (MODEL-0001 USER NAME: NOTE: When you COPY one model memory over another, everything you change MODEL TYPE or do a MODEL RESET, the entire memory is reset, including MODEL NAME want to do after you COPY a model, change its type, or start from scratch, is rename the new copy to avoid confusion. GOAL of EXAMPLE: STEPS: INPUTS: Open MODEL NAME submenu. for 1 second. to MODEL NAME. to C. Change the next character. (Ex: O to a) to a. (note: lower case is available) Where next? Repeat the prior steps to complete Repeat. naming the model. Close. Change the MODEL TYPE to airplane or helicopter: see p. 30. Change modulation [SFHSS or FHSS]: see p. 31. Utilize servo REVERSE: see p. 35. Adjust servo travel with END POINT: see p. 36. Set up dual/triple rates and exponential (D/R,EXP): see p. 39. GOAL of EXAMPLE: STEPS: INPUTS: Name USER NAME Open MODEL NAME submenu. for 1 second. 29 to MODEL NAME. Go to USER NAME and select the first USER NAME. to F. to u. (note: lower case is available) Repeat the prior steps to complete Repeat. naming the system. Close.
PARAMETER submenu: (ACRO) (HELI) S-FHSS or FHSS]? trim on channel 3 (ATL)? using the MODEL RESET: see p. 28. MODEL TYPE: sets the type of programming used for this model. The T8J has 20 model memories, which can each support: ACRO elevator servos, ELEVON, and V-TAIL for further information.) MODEL TYPE for details, p. 30. MODEL TYPE (Each model memory may be set to a different model type.) If your transmitter is a T8JA, the default is ACRO. If it is a HELI(H1). ACRO is the best choice for most powered airplanes: ACRO adds: SNAP-ROLL AILEVATOR (twin elevator servo support) IDLE-DOWN, THR-CUT, THROTTLE-NEEDLE mixing and THROTTLE DELAY programming. MODEL TYPE MODEL TYPE GOAL of EXAMPLE: STEPS: INPUTS: Select the proper MODEL TYPE for your Open the menu, then open the for 1 second. model. Ex: ACRO. PARAMETER submenu. to PARAMETER. [NOTE: This is one of several functions Go to MODEL TYPE. to TYPE. Select proper MODEL TYPE. Ex: ACRO. to ACROBATIC. for 1 second. Sure? displays. 30
Page 2: 8J-2.4GHz 8-CHANNEL RADIO CONTROL S
Page 5 and 6: 1. This product may be used for mod
Page 7 and 8: as well as the presence and locatio
Page 13 and 14: INSTALLATION AND REMOVAL OF THE TRA
Page 15 and 16: RECEIVER AND SERVO CONNECTIONS Rece
Page 18 and 19: RANGE CHECK THE RADIO adequate o
Page 21 and 22: Antenna *The two antennas should be
Page 28 and 29: A LOOK AT THE RADIO'S FUNCTIONS STE
Page 32 and 33: Receiver modulation select (RX): se
Page 37 and 38: End Point of servo travel adjustmen
Page 39 and 40: Throttle cut (THR-CUT): provides an
Page 41 and 42: GOAL of EXAMPLE: STEPS: INPUTS: Set
Page 45 and 46: TRAINER: for training novice pilots
Page 47 and 48: SUB-TRIM the default being no SUB-T
Page 49 and 50: FailSafe (loss of clean signal and
Page 51 and 52: Using FLAPERON (ACRO): The FLAPERON
Page 53 and 54: Using Aileron Differential (AILE-DI
Page 55 and 56: Dual Elevator Servos (with a rudder
Page 57 and 58: SNAP-ROLL) (ACRO): the same input
Page 59: MIXES: Mixes are special programs
Page 63 and 64: THROTTLE-NEEDLE mixing (ACRO/HELI):
Page 65 and 66: Throttle curve (THR-CURVE)(ACRO): A
Page 67 and 68: On/off choices: SWITCH: Any of the
Page 69 and 70: CURVE PROGRAMMABLE MIXES (PROG.MIX5
Page 71 and 72: GYA gyro mixing FLAPERON.
Page 73 and 74: HELICOPTER (HELI) MODEL FUNCTIONS
Page 75 and 76: GOAL of EXAMPLE: STEPS: INPUTS: Cha
Page 79 and 80: Setting up the Normal Flight Condit
Page 84 and 85:
OFFSET: Optional separate trims in
Page 86 and 87:
HOVERING ADJUSTMENTS (HOV-THR and H
Page 88 and 89:
System) technology. These sensors,
Page 90:
GOVERNORS: Magnetic sensor Control
show all

INSTRUCTION MANUAL - Scorpio

Create successful ePaper yourself

Delete template?

Save as template?