INSTRUCTION MANUAL - Scorpio

More documents

Recommendations

Info

GOAL of EXAMPLE: STEPS: INPUTS: Set up a FLAP-ELEV mix: Open an unused programmable mix. for 1 second. (Ex: use P.MIX3 ON when SWITCH C is in the down for FLAP-ELEVATOR.) to P.MIX1-6. position. to 3 Activate the function. to MIX. to ON. up (spoilers), Choose master and slave channels. already FLP (Ex: no need to change MASTER/SLAVE.) already ELE OFS, DT5, DT6 or to move down, MASTER. to desired VR choice. TRIM is not Set TRIM as needed. (Ex: leave TRIM not available.) Assign SWITCH and position. to SW. to C. (Ex: change to C, DOWN.) to POSI. to DOWN. Optional: set switch to THR to activate to SW. to THR. THROTTLE STICK to POSI. THROTTLE STICK to desired point. Optional: set switch position to NULL THR Set rates. (Ex: Lo=0%5%.) to RATE. 67 for 1 second to set. to POSI. to NULL. VR past center. Leave at 0%. VR past center. to 5%. Set OFFST, if needed. (Ex: 0.) to OFFST. Leave at 0%. Close menu. Where next? Adjust servo END POINTs: see p. 36. Setup dual/triple rates and exponential (D/R,EXP): see p. 39. Set up additional programmable mixes, ex: RUDDERAILERON: see p. 65. RUD-ELEV (ACRO) mix: Compensate for pitching up or down when rudder is applied. AIL-RUD (ACRO): Coordinate turns by applying rudder automatically with aileron input. All model types. ELEV-PIT (HELI) mix: compensate for the loss of lift of tilting the model.
CURVE PROGRAMMABLE MIXES (PROG.MIX5-6): ACRO/HELI programs contain two separate curve programmable mixes. There are a variety of reasons you might curve mix is the THROTTLE-NEEDLE at 5 points along its RPM range. One programmable curve mix defaults to RUDDER-AILERON ACRO The 2 programmable curve mixes default to the most frequent choices, but can be set to any channel. P.MIX5 P.MIX6 HELI P.MIX5 P.MIX6 The controlling channel can only be a channel. Cannot be OFFSET or dial. not available in curve mixes. Offset: not available in curve mixes. 68
Page 2:
8J-2.4GHz 8-CHANNEL RADIO CONTROL S
Page 5 and 6:
1. This product may be used for mod
Page 7 and 8:
as well as the presence and locatio
Page 13 and 14:
INSTALLATION AND REMOVAL OF THE TRA
Page 15 and 16:
RECEIVER AND SERVO CONNECTIONS Rece
Page 18 and 19: RANGE CHECK THE RADIO adequate o
Page 21 and 22: Antenna *The two antennas should be
Page 28 and 29: A LOOK AT THE RADIO'S FUNCTIONS STE
Page 30 and 31: MODEL NAME/USER NAME: MODEL NAME as
Page 32 and 33: Receiver modulation select (RX): se
Page 37 and 38: End Point of servo travel adjustmen
Page 39 and 40: Throttle cut (THR-CUT): provides an
Page 41 and 42: GOAL of EXAMPLE: STEPS: INPUTS: Set
Page 45 and 46: TRAINER: for training novice pilots
Page 47 and 48: SUB-TRIM the default being no SUB-T
Page 49 and 50: FailSafe (loss of clean signal and
Page 51 and 52: Using FLAPERON (ACRO): The FLAPERON
Page 53 and 54: Using Aileron Differential (AILE-DI
Page 55 and 56: Dual Elevator Servos (with a rudder
Page 57 and 58: SNAP-ROLL) (ACRO): the same input
Page 59: MIXES: Mixes are special programs
Page 63 and 64: THROTTLE-NEEDLE mixing (ACRO/HELI):
Page 65 and 66: Throttle curve (THR-CURVE)(ACRO): A
Page 67: On/off choices: SWITCH: Any of the
Page 71 and 72: GYA gyro mixing FLAPERON.
Page 73 and 74: HELICOPTER (HELI) MODEL FUNCTIONS
Page 75 and 76: GOAL of EXAMPLE: STEPS: INPUTS: Cha
Page 79 and 80: Setting up the Normal Flight Condit
Page 84 and 85: OFFSET: Optional separate trims in
Page 86 and 87: HOVERING ADJUSTMENTS (HOV-THR and H
Page 88 and 89: System) technology. These sensors,
Page 90: GOVERNORS: Magnetic sensor Control
show all

INSTRUCTION MANUAL - Scorpio

Create successful ePaper yourself

Delete template?

Save as template?