Statement List (STL) - DCE FEL ČVUT v Praze

More documents

Recommendations

Info

Timer Instructions 12.11 SF Off-Delay Timer Format SF Address Data type Memory area Description TIMER T Timer number, range depends on CPU Description of instruction Status word Example SF starts the addressed timer when the RLO transitions from "1" to "0". The programmed time elapses as long as RLO = 0. The time is stopped if RLO transitions to "1" before the programmed time interval has expired. This timer start command expects the time value and the time base to be stored as a BCD number in ACCU 1-L. See also Location of a Timer in Memory and Components of a Timer. BIE A1 A0 OV OS OR STA VKE /ER writes: - - - - - 0 - - 0 STL Explanation A I 2.0 FR T1 //Enable timer T1. A I 2.1 L S5T#10s //Preset 10 seconds into ACCU 1. SF T1 //Start timer T1 as an off-delay timer. A I 2.2 R T1 //Reset timer T1. A T1 //Check signal state of timer T1. = Q 4.0 L T1 //Load current timer value of timer T1 as binary. T MW10 LC T1 //Load current timer value of timer T1 as BCD. T MW12 Statement List (STL) for S7-300 and S7-400 Programming 12-20 A5E00706960-01
Enable input Start input Reset input Timer Output Load timer: L, LC I 2.0 I 2.1 I 2.2 Q 4.0 t t = programmed time interval Timer Instructions Statement List (STL) for S7-300 and S7-400 Programming A5E00706960-01 12-21 t
Page 1 and 2:
s SIMATIC Statement List (STL) for
Page 3 and 4:
Preface Purpose This manual is your
Page 5 and 6:
Preface Online Help The manual is c
Page 7 and 8:
Contents 1 Bit Logic Instructions 1
Page 9 and 10:
Contents 8 Floating-Point Math Inst
Page 11 and 12:
Contents 14 Accumulator Instruction
Page 13 and 14:
1 Bit Logic Instructions 1.1 Overvi
Page 15 and 16:
1.2 A And Format A Address Data ty
Page 17 and 18:
1.4 O Or Format O Address Data typ
Page 19 and 20:
1.6 X Exclusive Or Format X Addres
Page 21 and 22:
1.8 O And before Or Format Descript
Page 23 and 24:
1.10 AN( And Not with Nesting Open
Page 25 and 26:
1.14 XN( Exclusive Or Not with Nest
Page 27 and 28:
Example Statement List Program A( O
Page 29 and 30:
1.17 R Reset Format R Address Data
Page 31 and 32:
1.19 NOT Negate RLO Format Descript
Page 33 and 34:
1.21 CLR Clear RLO (=0) Format Desc
Page 35 and 36:
1.23 FN Edge Negative Format FN Bi
Page 37 and 38:
1.24 FP Edge Positive Format FP Bi
Page 39 and 40:
2 Comparison Instructions 2.1 Overv
Page 41 and 42:
2.3 ? D Compare Double Integer (32-
Page 43 and 44:
3 Conversion Instructions 3.1 Overv
Page 45 and 46:
3.3 ITB Integer (16-Bit) to BCD For
Page 47 and 48:
3.5 ITD Integer (16 Bit) to Double
Page 49 and 50:
Conversion Instructions 3.7 DTR Dou
Page 51 and 52:
Conversion Instructions 3.9 INVD On
Page 53 and 54:
Conversion Instructions 3.11 NEGD T
Page 55 and 56:
Conversion Instructions 3.13 CAW Ch
Page 57 and 58:
3.15 RND Round Format Description S
Page 59 and 60:
3.17 RND+ Round to Upper Double Int
Page 61 and 62:
4 Counter Instructions 4.1 Overview
Page 63 and 64:
4.3 L Load Current Counter Value in
Page 65 and 66:
4.5 R Reset Counter Format Descript
Page 67 and 68:
4.7 CU Counter Up Format CU Counte
Page 69 and 70:
5 Data Block Instructions 5.1 Overv
Page 71 and 72:
5.3 CDB Exchange Shared DB and Inst
Page 73 and 74:
Data Block Instructions 5.6 L DILG
Page 75 and 76:
6 Logic Control Instructions 6.1 Ov
Page 77 and 78:
6.2 JU Jump Unconditional Format De
Page 79 and 80:
6.4 JC Jump if RLO = 1 Format Descr
Page 81 and 82:
6.6 JCB Jump if RLO = 1 with BR For
Page 83 and 84:
6.8 JBI Jump if BR = 1 Format Descr
Page 85 and 86:
6.10 JO Jump if OV = 1 Format Descr
Page 87 and 88:
6.12 JZ Jump if Zero Format Descrip
Page 89 and 90:
6.14 JP Jump if Plus Format Descrip
Page 91 and 92:
6.16 JPZ Jump if Plus or Zero Forma
Page 93 and 94:
6.18 JUO Jump if Unordered Format D
Page 95 and 96:
7 Integer Math Instructions 7.1 Ove
Page 97 and 98:
Integer Math Instructions 7.3 +I Ad
Page 99 and 100:
Integer Math Instructions 7.5 *I Mu
Page 101 and 102:
Example: 13 divided by 4 Contents o
Page 103 and 104:
Example 3 STL Explanation L MD20 L
Page 105 and 106:
Integer Math Instructions 7.9 -D Su
Page 107 and 108:
Integer Math Instructions 7.11 /D D
Page 109 and 110:
Integer Math Instructions 7.12 MOD
Page 111 and 112:
8 Floating-Point Math Instructions
Page 113 and 114:
8.3 Floating-Point Math Instruction
Page 115 and 116:
Floating-Point Math Instructions 8.
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
9 Load and Transfer Instructions 9.
Page 133 and 134:
Contents of ACCU 1 Load and Transfe
Page 135 and 136:
Load and Transfer Instructions 9.4
Page 137 and 138:
Page 139 and 140:
9.9 T Transfer Format Description S
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
10 Program Control Instructions 10.
Page 147 and 148:
10.3 BEC Block End Conditional Form
Page 149 and 150:
10.5 CALL Block Call Format Descrip
Page 151 and 152:
10.6 Call FB Format Description CAL
Page 153 and 154:
10.7 Call FC Format Description CAL
Page 155 and 156:
10.8 Call SFB Format Description CA
Page 157 and 158: 10.9 Call SFC Format Description CA
Page 159 and 160: 10.12 CC Conditional Call Format De
Page 161 and 162: 10.14 MCR (Master Control Relay) !
Page 163 and 164: 10.15 Important Notes on Using MCR
Page 165 and 166: Example Program Control Instruction
Page 167 and 168: 10.18 MCRA Activate MCR Area Format
Page 169 and 170: 11 Shift and Rotate Instructions 11
Page 171 and 172: Example 1 STL Explanation L MW4 //L
Page 173 and 174: Examples Shift and Rotate Instructi
Page 183 and 184: 11.2.2 RLD Rotate Left Double Word
Page 185 and 186: 11.2.3 RRD Rotate Right Double Word
Page 187 and 188: 11.2.4 RLDA Rotate ACCU 1 Left via
Page 189 and 190: 12 Timer Instructions 12.1 Overview
Page 191 and 192: Time Base Timer Instructions Bits 1
Page 193 and 194: 12.3 FR Enable Timer (Free) Format
Page 195 and 196: Timer Instructions 12.4 L Load Curr
Page 197 and 198: Timer Instructions 12.5 LC Load Cur
Page 199 and 200: 12.6 R Reset Timer Format R Timer
Page 201 and 202: Enable input Start input Reset inpu
Page 203 and 204: Enable input Start input Reset inpu
Page 205 and 206: Enable Input Start Input Reset Inpu
Page 207: Enable input Start input Reset inpu
Page 211 and 212: 13 Word Logic Instructions 13.1 Ove
Page 213 and 214: Examples Word Logic Instructions Bi
Page 225 and 226: 14 Accumulator Instructions 14.1 Ov
Page 227 and 228: 14.3 POP CPU with Two ACCUs Format
Page 229 and 230: 14.5 PUSH CPU with Two ACCUs Format
Page 231 and 232: 14.7 ENT Enter ACCU Stack Format De
Page 233 and 234: 14.10 DEC Decrement ACCU 1-L-L Form
Page 235 and 236: 14.12 +AR2 Add ACCU 1 to Address Re
Page 237 and 238: 14.15 NOP 1 Null Instruction Format
Page 239 and 240: A Overview of All STL Instructions
Page 241 and 242: German Mnemonics English Mnemonics
Page 243 and 244: German Mnemonics English Mnemonics
Page 245 and 246: Overview of All STL Instructions A.
Page 247 and 248: English Mnemonics German Mnemonics
Page 249 and 250: English Mnemonics German Mnemonics
Page 251 and 252: B Programming Examples B.1 Overview
Page 253 and 254: Absolute and symbolic Programming P
Page 255 and 256: Absolute and symbolic Programming P
Page 257 and 258: B.3 Example: Timer Instructions Clo
Page 259 and 260:
Signal states of the Bits of Memory
Page 261 and 262:
Statement List that Activates the I
Page 263 and 264:
B.6 Example: Word Logic Instruction
Page 265 and 266:
C Parameter Transfer ! The paramete
Page 267 and 268:
Index ) ) .........................
Page 269 and 270:
I -I ..............................
Page 271 and 272:
SLD................................
show all

Statement List (STL) - DCE FEL ČVUT v Praze

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?