WM, Workshop Manual, K650, K700, K950, K1250, 2001-06, Power ...

More documents

Recommendations

Info

Starter unit 1 Tension the return spring. Check that the spring tension is completely released, and lift the starter cord up into the cut-out in the pulley. Tension the return spring. 1. Check that spring tension is competely released. 2. Lift the starter cord up into the cut-out in the pulley. Wind the pulley 7 turns clockwise. 3. Wind the pulley 7 turns clockwise. Be careful and brake the pulley with your thumb. Max Pull the cord out completely and check that the pulley can be turned at least a further half turn. 4. Pull the cord out completely and check that the pulley can be turned at least a further half turn. +1/2 Mod. 1250 Press down a new return spring in the starter unit cover. Mod. 1250 Press a new return spring down in the starter unit cover. Lubricate the spring with a few drops of oil. Anchor the cord in the pulley. Push the pulley down onto the shaft journal. NOTE! Do not remove the lock round the spring, but push down the spring all round by using your thumbs. Lubricate the spring with a few drops of oil. Anchor the starter cord round the hub of the pulley as shown in the diagram. Push the cord wheel down on the shaft journal in the starter unit housing. Make sure that the spring grips the cord wheel. Lubricate the bearing with a few drops of oil. 9
1 Anchor the starter cord in the starter handle with a double knot. Enter the cord through the cord guide in the starter unit and anchor it in the starter handle with a double knot. Fit the starter unit and other parts in the reverse order to dismantling. Fit the starter unit. Pull out the starter cord a little. Place the starter unit in position. Release the starter cord and check that the pawls engage the pulley. Tighten the screws. 10
Page 1 and 2: PARTNER Workshop Manual R
Page 3 and 4: General recommendations Keep this i
Page 5 and 6: 1 Starter unit ! WARNING! When work
Page 7 and 8: 1 Starter unit Anchor the starter r
Page 9: 1 Starter unit Assembly Mod. 650, 7
Page 13 and 14: 2 Ignition system The engine is fit
Page 15 and 16: 2 Ignition system Check the ignitio
Page 17 and 18: 2 Ignition system Fit piston stop N
Page 19 and 20: 2 Ignition system Fit the ignition
Page 21 and 22: 3 Fuel system In addition to the fu
Page 23 and 24: 15 10 5 20 0 100 50 0 150 30 200 25
Page 25 and 26: 3 Fuel system A Dismantle the screw
Page 27 and 28: 3 Fuel system Speed limiter Mod. 65
Page 29 and 30: 3 Fuel system In the event of leaka
Page 31 and 32: 3 Fuel system Assembly of the carbu
Page 33 and 34: 3 Fuel system Walbro WG 9 A C B Mod
Page 35 and 36: 3 Fuel system Fine adjustment of th
Page 37 and 38: 3 Fuel system Lift off the half of
Page 39 and 40: 3 Fuel system Mod. 1250 Separate th
Page 41 and 42: 3 Fuel system Trouble-shooting char
Page 43 and 44: 4 Centrifugal clutch The centrifuga
Page 45 and 46: 4 Centrifugal clutch Mod. 950, 1250
Page 47 and 48: 4 Centrifugal clutch The clutch dru
Page 49 and 50: 5 Cylinder and piston The cylinder
Page 51 and 52: 5 Cylinder and piston Unscrew the c
Page 53 and 54: 5 Cylinder and piston Piston seizur
Page 55 and 56: 5 Cylinder and piston Reasons: ●
Page 57 and 58: 5 Cylinder and piston Fit a new cyl
Page 59 and 60: 5 Cylinder and piston Check that th
Page 61 and 62:
6 Crankshaft and crankcase The purp
Page 63 and 64:
6 Crankshaft and crankcase Mod. 950
Page 65 and 66:
6 Crankshaft and crankcase Remove t
Page 67 and 68:
6 Crankshaft and crankcase Mod. 125
Page 69 and 70:
6 Crankshaft and crankcase Heat up
Page 71 and 72:
6 Crankshaft and crankcase M5 x 20
Page 73 and 74:
6 Crankshaft and crankcase Check th
Page 75 and 76:
6 Model 950 - Crankcase lubrication
Page 78 and 79:
Cutting equipment 7. Contents Disma
Page 80 and 81:
Cutting equipment 7 Release the bel
Page 82 and 83:
Cutting equipment 7 D E F Turn the
Page 84 and 85:
Cutting equipment 7 B A Lift the cu
Page 86 and 87:
Tools 8. Contents Clutch ..........
Page 88 and 89:
Tools 8 Sealing ring Model 505 38 1
Page 90 and 91:
15 10 5 100 50 0 150 30 200 250 300
Page 92 and 93:
Tools 8 Workshop equipment Model 3
Page 94 and 95:
Technical data 9. Contents Technica
Page 96:
108 07 07-47 SEK 95:- Teknik-Info A
show all

WM, Workshop Manual, K650, K700, K950, K1250, 2001-06, Power ...

Create successful ePaper yourself

Delete template?

Save as template?