WM, Workshop Manual, K650, K700, K950, K1250, 2001-06, Power ...

More documents

Recommendations

Info

Workshop Manual Petrol power cutters Contents General recommendations .................................................. 2 1. Starter unit ......................................................................... 3 2. Ignition system ............................................................... 11 3. Fuel system ..................................................................... 19 4. Centrifugal clutch ........................................................... 41 5. Cylinder and piston ........................................................ 47 6. Crankshaft and crankcase ............................................. 59 7. Cutting equipment .......................................................... 77 8. Tools ................................................................................. 85 9. Technical data ................................................................. 93 This manual covers models: K 650/700 Active K 950/1250 Active © Copyright Partner Industrial Products, Sweden 1
General recommendations Keep this in mind: ! ! ! ! ! ! Do not start the engine unless the clutch and clutch drum are fitted. Do not touch hot parts, e.g. silencer and clutch, before they have cooled sufficiently to avoid burn injuries. Avoid getting petrol or oil on the skin or in the mouth. Use protective cream on the hands. This reduces the risk of infection and makes it easier to wash off dirt. Prolonged exposure to engine oil can be hazardous to health. Never start the engine indoors. The exhaust fumes are toxic!. Wipe up spilled oil immediately from the floor to avoid slipping. Do not use tools which are worn or have a poor fit, e.g. nuts and screws. + Always work on a clean work bench. + Always work in a logical way to make sure that all parts are correctly fitted and that screws and nuts are tightened. + Use special tools where so recommended in order to do the work correctly. Special tools Some work procedures in this Workshop Manual require the use of special tools. In each section where this is appropriate the tool and order number are illustrated. We recommend the use of special tools partly to avoid personal injury and partly to eliminate expensive damage to the components in question. Sealing surfaces and gaskets Make sure that all sealing surfaces are clean and free from the residue of old gaskets. Use a tool which will not damage the sealing surface when cleaning it. Scratches and irregularities are removed with a fine, float cut file. Sealing rings Always replace a sealing ring which has been dismantled. The sensitive sealing lip can easily be damaged and result in poor sealing capacity. The surface which the seal seals must also be completely undamaged. Lubricate the sealing lip with grease before it is fitted and make sure that it is not damaged, e.g. by the shoulder and splines on a shaft. Use tape or a conical sleeve as protection. It is important that the sealing ring is correctly turned for it to function as intended. Fire hazard Handle petrol with respect since it is highly inflammable. Do not smoke, and make sure that there are no naked flames or sparks in the vicinity. Make sure that there is a functioning fire extinguisher in the vicinity. Do not try to extinguish a petrol fire with water. Use an anti-spill fuel can. Toxic fumes Read the instructions carefully when using cleaning liquids. Make sure that there is adequate ventilation when handling petrol and other viscous liquids. The engine exhaust fumes are toxic. Test run the engine outdoors. ! WARNING The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. 2
Page 1: PARTNER Workshop Manual R
Page 5 and 6: 1 Starter unit ! WARNING! When work
Page 7 and 8: 1 Starter unit Anchor the starter r
Page 9 and 10: 1 Starter unit Assembly Mod. 650, 7
Page 11 and 12: 1 Anchor the starter cord in the st
Page 13 and 14: 2 Ignition system The engine is fit
Page 15 and 16: 2 Ignition system Check the ignitio
Page 17 and 18: 2 Ignition system Fit piston stop N
Page 19 and 20: 2 Ignition system Fit the ignition
Page 21 and 22: 3 Fuel system In addition to the fu
Page 23 and 24: 15 10 5 20 0 100 50 0 150 30 200 25
Page 25 and 26: 3 Fuel system A Dismantle the screw
Page 27 and 28: 3 Fuel system Speed limiter Mod. 65
Page 29 and 30: 3 Fuel system In the event of leaka
Page 31 and 32: 3 Fuel system Assembly of the carbu
Page 33 and 34: 3 Fuel system Walbro WG 9 A C B Mod
Page 35 and 36: 3 Fuel system Fine adjustment of th
Page 37 and 38: 3 Fuel system Lift off the half of
Page 39 and 40: 3 Fuel system Mod. 1250 Separate th
Page 41 and 42: 3 Fuel system Trouble-shooting char
Page 43 and 44: 4 Centrifugal clutch The centrifuga
Page 45 and 46: 4 Centrifugal clutch Mod. 950, 1250
Page 47 and 48: 4 Centrifugal clutch The clutch dru
Page 49 and 50: 5 Cylinder and piston The cylinder
Page 51 and 52: 5 Cylinder and piston Unscrew the c
Page 53 and 54:
5 Cylinder and piston Piston seizur
Page 55 and 56:
5 Cylinder and piston Reasons: ●
Page 57 and 58:
5 Cylinder and piston Fit a new cyl
Page 59 and 60:
5 Cylinder and piston Check that th
Page 61 and 62:
6 Crankshaft and crankcase The purp
Page 63 and 64:
6 Crankshaft and crankcase Mod. 950
Page 65 and 66:
6 Crankshaft and crankcase Remove t
Page 67 and 68:
6 Crankshaft and crankcase Mod. 125
Page 69 and 70:
6 Crankshaft and crankcase Heat up
Page 71 and 72:
6 Crankshaft and crankcase M5 x 20
Page 73 and 74:
6 Crankshaft and crankcase Check th
Page 75 and 76:
6 Model 950 - Crankcase lubrication
Page 78 and 79:
Cutting equipment 7. Contents Disma
Page 80 and 81:
Cutting equipment 7 Release the bel
Page 82 and 83:
Cutting equipment 7 D E F Turn the
Page 84 and 85:
Cutting equipment 7 B A Lift the cu
Page 86 and 87:
Tools 8. Contents Clutch ..........
Page 88 and 89:
Tools 8 Sealing ring Model 505 38 1
Page 90 and 91:
15 10 5 100 50 0 150 30 200 250 300
Page 92 and 93:
Tools 8 Workshop equipment Model 3
Page 94 and 95:
Technical data 9. Contents Technica
Page 96:
108 07 07-47 SEK 95:- Teknik-Info A
show all

WM, Workshop Manual, K650, K700, K950, K1250, 2001-06, Power ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?