WM, Workshop Manual, K650, K700, K950, K1250, 2001-06, Power ...

More documents

Recommendations

Info

Cutting equipment 7 B A Lift the cutter arm in position and fit the front belt guard and belt tensioning device. Tension the drive belt and tighten the nuts. Lift the cutter arm in position. Place the front guard and belt tensioning device in position. Tighten the nuts loosely. Tension the drive belt at the same time as the cutting disc is rotated, then tighten the nuts. Tension the drive belt by screwing in the tensioning screw (A) far enough so that the square nut (B) comes opposite the arrow (C). Rotate the cutting disc at the same time as the drive belt is tensioned. Thereafter tighten the nuts. TIP! C Install a diamond cutting disk and wash the circular saw up for about 2 minutes. Check the belt tension and re-tension the belt if necessary. Dismantling Dismantling Mod. 950, 1250 Mod. 950, 1250 Dismantle the cutter disc, belt covers, drive belt, belt disc, support washers and spacer sleeve in the usual way. Dismantle the cutter disc, belt covers, drive belt, and pulley in the same way as for mod. 650, 700. TIP! If only the spacer sleeve and the inner support washer are to be dismantled this can be done by bending with two spanners placed between the spacer sleeve and the support washer. Assembly Mod. 950, 1250 Follow the instructions for mod. 650, and 700. Note that the attachment of the burst protection to the cutter arm has a different design to the one shown in the illustration. Fit the drive belt and the rear belt cover in the same way as for mod. 650, 700. Fit the drive belt and the rear belt cover in the same way as for mod. 650, and 700. Tension the belt correctly and tighten the screws which hold the front belt cover. 83
7 Cutting equipment Fit the cutter arm Tension as the drive belt at the same time as the cutting disc is rotated, and tighten the two nuts. Lift the cutter arm in place. Fit the drive belt over the front pulley. Push the front belt cover in place and screw down the attachment screws half way. Tension the drive belt in the same way as for mod. 650, and 700, and then tighten the two screws. TIP! Install a diamond cutting disc and warm the circular saw up for about 2 minutes. Check the belt tension and re-tension the belt if necessary. 84
Page 1 and 2:
PARTNER Workshop Manual R
Page 3 and 4:
General recommendations Keep this i
Page 5 and 6:
1 Starter unit ! WARNING! When work
Page 7 and 8:
1 Starter unit Anchor the starter r
Page 9 and 10:
1 Starter unit Assembly Mod. 650, 7
Page 11 and 12:
1 Anchor the starter cord in the st
Page 13 and 14:
2 Ignition system The engine is fit
Page 15 and 16:
2 Ignition system Check the ignitio
Page 17 and 18:
2 Ignition system Fit piston stop N
Page 19 and 20:
2 Ignition system Fit the ignition
Page 21 and 22:
3 Fuel system In addition to the fu
Page 23 and 24:
15 10 5 20 0 100 50 0 150 30 200 25
Page 25 and 26:
3 Fuel system A Dismantle the screw
Page 27 and 28:
3 Fuel system Speed limiter Mod. 65
Page 29 and 30:
3 Fuel system In the event of leaka
Page 31 and 32:
3 Fuel system Assembly of the carbu
Page 33 and 34: 3 Fuel system Walbro WG 9 A C B Mod
Page 35 and 36: 3 Fuel system Fine adjustment of th
Page 37 and 38: 3 Fuel system Lift off the half of
Page 39 and 40: 3 Fuel system Mod. 1250 Separate th
Page 41 and 42: 3 Fuel system Trouble-shooting char
Page 43 and 44: 4 Centrifugal clutch The centrifuga
Page 45 and 46: 4 Centrifugal clutch Mod. 950, 1250
Page 47 and 48: 4 Centrifugal clutch The clutch dru
Page 49 and 50: 5 Cylinder and piston The cylinder
Page 51 and 52: 5 Cylinder and piston Unscrew the c
Page 53 and 54: 5 Cylinder and piston Piston seizur
Page 55 and 56: 5 Cylinder and piston Reasons: ●
Page 57 and 58: 5 Cylinder and piston Fit a new cyl
Page 59 and 60: 5 Cylinder and piston Check that th
Page 61 and 62: 6 Crankshaft and crankcase The purp
Page 63 and 64: 6 Crankshaft and crankcase Mod. 950
Page 65 and 66: 6 Crankshaft and crankcase Remove t
Page 67 and 68: 6 Crankshaft and crankcase Mod. 125
Page 69 and 70: 6 Crankshaft and crankcase Heat up
Page 71 and 72: 6 Crankshaft and crankcase M5 x 20
Page 73 and 74: 6 Crankshaft and crankcase Check th
Page 75 and 76: 6 Model 950 - Crankcase lubrication
Page 78 and 79: Cutting equipment 7. Contents Disma
Page 80 and 81: Cutting equipment 7 Release the bel
Page 82 and 83: Cutting equipment 7 D E F Turn the
Page 86 and 87: Tools 8. Contents Clutch ..........
Page 88 and 89: Tools 8 Sealing ring Model 505 38 1
Page 90 and 91: 15 10 5 100 50 0 150 30 200 250 300
Page 92 and 93: Tools 8 Workshop equipment Model 3
Page 94 and 95: Technical data 9. Contents Technica
Page 96: 108 07 07-47 SEK 95:- Teknik-Info A
show all

WM, Workshop Manual, K650, K700, K950, K1250, 2001-06, Power ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?