WM, Workshop Manual, K650, K700, K950, K1250, 2001-06, Power ...

More documents

Recommendations

Info

Crankshaft and crankcase 6 Remove the screws (B). Lift off the crankcase. Remove the screws (B). Lift off the crankcase. B B 505 38 13-08 Remove all crankcase screws. Remove all the screws (7 pcs) which hold the crankcase halves together. 505 38 13-08 Separate the crankcase halves. Separate the crankcase halves by means of tool 502 51 61-01. Start with the clutch side half. 502 51 61-01 Press out the crankshaft from the crankcase half. Use the same tool as above and press out the crankshaft from the crankcase half. Inspect the crankshaft according to the chapter ”Inspection of crankshaft”. 502 51 61-01 67
6 Crankshaft and crankcase Heat up the crankcase halves to 150° – 200° C. Dismantle the ball bearings. Press off the seal. Heat up the crankcase halves to 150° – 200° C with a hot air gun. Tap the crankcase half against a block of wood so that the ball bearing drops out. Press off the seal with a suitable drift. Clean the crankcase halves. Replace if necessary the screws for the cutter arm. Clean both crankcase halves. Make sure that the two guide pins are not misplaced. Carefully scrape off residual gasket from the sealing surfaces. Take the opportunity to replace the screws for the cutter arm if they are worn or damaged. Press them out with a hammer and drift. Fit new ball bearings and seals. Pull the crankshaft into the flywheel side’s crankcase half. Fit new ball bearings and seals. Heat up the crankcase half to 150° – 200° C and place the ball bearing in position. Pull the crankshaft into the flywheel side’s crankcase half with tool 502 50 30-10. Make sure that the connecting rod is not clenched against the crankcase. 502 50 30-10 Check that the guide pins are in position in the flywheel side’s crankcase half. Place a new gasket on the sealing surface. Check that the guide pins are in position in the flywheel side’s crankcase half. Apply grease to the sealing surface and place a new gasket over the guide pins. 68
Page 1 and 2:
PARTNER Workshop Manual R
Page 3 and 4:
General recommendations Keep this i
Page 5 and 6:
1 Starter unit ! WARNING! When work
Page 7 and 8:
1 Starter unit Anchor the starter r
Page 9 and 10:
1 Starter unit Assembly Mod. 650, 7
Page 11 and 12:
1 Anchor the starter cord in the st
Page 13 and 14:
2 Ignition system The engine is fit
Page 15 and 16:
2 Ignition system Check the ignitio
Page 17 and 18: 2 Ignition system Fit piston stop N
Page 19 and 20: 2 Ignition system Fit the ignition
Page 21 and 22: 3 Fuel system In addition to the fu
Page 23 and 24: 15 10 5 20 0 100 50 0 150 30 200 25
Page 25 and 26: 3 Fuel system A Dismantle the screw
Page 27 and 28: 3 Fuel system Speed limiter Mod. 65
Page 29 and 30: 3 Fuel system In the event of leaka
Page 31 and 32: 3 Fuel system Assembly of the carbu
Page 33 and 34: 3 Fuel system Walbro WG 9 A C B Mod
Page 35 and 36: 3 Fuel system Fine adjustment of th
Page 37 and 38: 3 Fuel system Lift off the half of
Page 39 and 40: 3 Fuel system Mod. 1250 Separate th
Page 41 and 42: 3 Fuel system Trouble-shooting char
Page 43 and 44: 4 Centrifugal clutch The centrifuga
Page 45 and 46: 4 Centrifugal clutch Mod. 950, 1250
Page 47 and 48: 4 Centrifugal clutch The clutch dru
Page 49 and 50: 5 Cylinder and piston The cylinder
Page 51 and 52: 5 Cylinder and piston Unscrew the c
Page 53 and 54: 5 Cylinder and piston Piston seizur
Page 55 and 56: 5 Cylinder and piston Reasons: ●
Page 57 and 58: 5 Cylinder and piston Fit a new cyl
Page 59 and 60: 5 Cylinder and piston Check that th
Page 61 and 62: 6 Crankshaft and crankcase The purp
Page 63 and 64: 6 Crankshaft and crankcase Mod. 950
Page 65 and 66: 6 Crankshaft and crankcase Remove t
Page 67: 6 Crankshaft and crankcase Mod. 125
Page 71 and 72: 6 Crankshaft and crankcase M5 x 20
Page 73 and 74: 6 Crankshaft and crankcase Check th
Page 75 and 76: 6 Model 950 - Crankcase lubrication
Page 78 and 79: Cutting equipment 7. Contents Disma
Page 80 and 81: Cutting equipment 7 Release the bel
Page 82 and 83: Cutting equipment 7 D E F Turn the
Page 84 and 85: Cutting equipment 7 B A Lift the cu
Page 86 and 87: Tools 8. Contents Clutch ..........
Page 88 and 89: Tools 8 Sealing ring Model 505 38 1
Page 90 and 91: 15 10 5 100 50 0 150 30 200 250 300
Page 92 and 93: Tools 8 Workshop equipment Model 3
Page 94 and 95: Technical data 9. Contents Technica
Page 96: 108 07 07-47 SEK 95:- Teknik-Info A
show all

WM, Workshop Manual, K650, K700, K950, K1250, 2001-06, Power ...

Create successful ePaper yourself

Delete template?

Save as template?