WM, Workshop Manual, K650, K700, K950, K1250, 2001-06, Power ...

More documents

Recommendations

Info

Crankshaft and crankcase 6 Push the crankcase halves together and tighten the crankcase screws. Place the clutch side’s crankcase half over the crankshaft. Position the crankcase screws to prevent the gasket from sliding out of position. Push the crankcase halves together with tool 502 50 30-10. Tighten all the crankcase screws. 502 50 30-10 Check that the crankshaft rotates easily. Lubricate the shaft journals with a few drops of oil and fit the seals. Check that the crankshaft rotates easily. If not, tap the shaft journals a few times with a plastic mallet to release any tension. Lubricate the shaft journals with a few drops of oil and fit the seals. The casing should face outwards. Use assembly sleeve 505 38 17-23 on the clutch side. 505 38 17-23 M5x55 M5x12 Fit the handle unit. Start with the rear handle. Make sure that the throttle push rod and stop wire are correctly positioned. Fit the handle unit. Start with the rear handle. Make sure that the throttle push rod and stop wire are correctly positioned. M5x12 Note the different lengths of the screws. Note the different lengths of the screws. M5x25 M5x55 M5x20 505 38 13-08 Repair bushing Models 650, 700 On old model crankcases, the cylinder cover screw is screwed directly into the casting. The threads may be damaged as time passes. Repair bushing No. 503 27 35-99 can then be installed instead of replacing the entire crankcase. Drill out the hole in 3 stages, using drills of Ø 7 mm, Ø 8 mm and Ø 9 mm. 69
6 Crankshaft and crankcase M5 x 20 mm Pull the repair bushing into place with an M5 screw and washer as shown in theillustration. NOTE! Align the bushing correctly, so that the chamfered section faces the cylinder plane. 503 27 35-99 Mod. 950 Remove all screws which hold the crankcase halves together. Mod. 950 Dismantle all parts so that only the crankcase and crankshaft remain. Remove all screws (9 items) which hold the two crankcase halves together. Separate and fit the crankcase halves in same way as described for mod. 650, 700. Separate and assemble the crankcase halves in the same way as described for mod. 650, 700. Inspect the crankshaft (see chapter ”Inspection of crankshaft”). Use tool 502 50 30-08 to assemble. Use protective sleeve No. 502 50 52-01 when the seal ring on the clutch side is installed. A 502 51 61-01 502 50 30-08 Mod. 1250 Dismantle the cutter arm. Mod. 1250 Dismantle all parts so that only the crankcase with crankshaft remain. Dismantle the cutter arm by removing the nut (A) and screws (B). B 70
Page 1 and 2:
PARTNER Workshop Manual R
Page 3 and 4:
General recommendations Keep this i
Page 5 and 6:
1 Starter unit ! WARNING! When work
Page 7 and 8:
1 Starter unit Anchor the starter r
Page 9 and 10:
1 Starter unit Assembly Mod. 650, 7
Page 11 and 12:
1 Anchor the starter cord in the st
Page 13 and 14:
2 Ignition system The engine is fit
Page 15 and 16:
2 Ignition system Check the ignitio
Page 17 and 18:
2 Ignition system Fit piston stop N
Page 19 and 20: 2 Ignition system Fit the ignition
Page 21 and 22: 3 Fuel system In addition to the fu
Page 23 and 24: 15 10 5 20 0 100 50 0 150 30 200 25
Page 25 and 26: 3 Fuel system A Dismantle the screw
Page 27 and 28: 3 Fuel system Speed limiter Mod. 65
Page 29 and 30: 3 Fuel system In the event of leaka
Page 31 and 32: 3 Fuel system Assembly of the carbu
Page 33 and 34: 3 Fuel system Walbro WG 9 A C B Mod
Page 35 and 36: 3 Fuel system Fine adjustment of th
Page 37 and 38: 3 Fuel system Lift off the half of
Page 39 and 40: 3 Fuel system Mod. 1250 Separate th
Page 41 and 42: 3 Fuel system Trouble-shooting char
Page 43 and 44: 4 Centrifugal clutch The centrifuga
Page 45 and 46: 4 Centrifugal clutch Mod. 950, 1250
Page 47 and 48: 4 Centrifugal clutch The clutch dru
Page 49 and 50: 5 Cylinder and piston The cylinder
Page 51 and 52: 5 Cylinder and piston Unscrew the c
Page 53 and 54: 5 Cylinder and piston Piston seizur
Page 55 and 56: 5 Cylinder and piston Reasons: ●
Page 57 and 58: 5 Cylinder and piston Fit a new cyl
Page 59 and 60: 5 Cylinder and piston Check that th
Page 61 and 62: 6 Crankshaft and crankcase The purp
Page 63 and 64: 6 Crankshaft and crankcase Mod. 950
Page 65 and 66: 6 Crankshaft and crankcase Remove t
Page 67 and 68: 6 Crankshaft and crankcase Mod. 125
Page 69: 6 Crankshaft and crankcase Heat up
Page 73 and 74: 6 Crankshaft and crankcase Check th
Page 75 and 76: 6 Model 950 - Crankcase lubrication
Page 78 and 79: Cutting equipment 7. Contents Disma
Page 80 and 81: Cutting equipment 7 Release the bel
Page 82 and 83: Cutting equipment 7 D E F Turn the
Page 84 and 85: Cutting equipment 7 B A Lift the cu
Page 86 and 87: Tools 8. Contents Clutch ..........
Page 88 and 89: Tools 8 Sealing ring Model 505 38 1
Page 90 and 91: 15 10 5 100 50 0 150 30 200 250 300
Page 92 and 93: Tools 8 Workshop equipment Model 3
Page 94 and 95: Technical data 9. Contents Technica
Page 96: 108 07 07-47 SEK 95:- Teknik-Info A
show all

WM, Workshop Manual, K650, K700, K950, K1250, 2001-06, Power ...

Create successful ePaper yourself

Delete template?

Save as template?