WM, Workshop Manual, K650, K700, K950, K1250, 2001-06, Power ...

More documents

Recommendations

Info

Crankshaft and crankcase 6 Remove all screws which hold the crankcase halves together. Remove all screws (9 items) which hold the two crankcase halves together. Separate and assemble the crankcase halves in the same way as described for mod. 650, 700. Separate and assemble the crankcase halves in the same way as described for mod. 650, 700. Inspect the crankshaft (see chapter ”Inspection of the crankshaft”). NOTE! The tool 502 51 61-01 cannot be used on the flywheel side. Heat instead the crankcase half with a hot air gun to approx. 110°C, and press off the crankshaft. Use tool 502 50 30-08 to assemble. 502 51 61-01 502 50 30-08 Inspection of crankshaft Check the connecting rod’s big end. Inspection of crankshaft The crankshaft cannot be renovated and must be replaced by a new one if it is worn or damaged. Check the connecting rod’s big end. If seizure marks or discolouring in the bearing race are discovered then the crankshaft should be replaced. Check the connecting rod’s small end. Check the connecting rod’s small end. If seizure marks or discolouring in the bearing race are discovered then the crankshaft should be replaced. 71
6 Crankshaft and crankcase Check the big end bearing. Check the big end bearing. There should be no radial play (upwards and downwards) on the connecting rod. It should, however, have an axial play to ensure good lubrication of the big end bearing. Blow clean the channel for the automatic lubrication of the clutch drum’s bearing. Mod. 650 and 700 have automatic lubrication of the clutch drum’s bearing. Check with compressed air that the lubrication channel is open. Pressure test All models Install blanking plates on the induction and exhaust sides of the cylinder. Connect the pressure gauge 502 50 38-01 to the nipple and pump up a pressure of 50 kPa (0.5 kp/cm 2 ) in the crankcase. Maximum permissible leakage: 20 kPa (0.2 kp/cm 2 ) per 30 seconds. 502 50 38-01 Models 650, 700 – Muffler side Remove the cutting equipment, muffler, exhaust gasket and cooling plate. Fix cover washer No. 502 54 02-01 to the cylinder with an M5x15 screw. 502 54 02-01 72
Page 1 and 2:
PARTNER Workshop Manual R
Page 3 and 4:
General recommendations Keep this i
Page 5 and 6:
1 Starter unit ! WARNING! When work
Page 7 and 8:
1 Starter unit Anchor the starter r
Page 9 and 10:
1 Starter unit Assembly Mod. 650, 7
Page 11 and 12:
1 Anchor the starter cord in the st
Page 13 and 14:
2 Ignition system The engine is fit
Page 15 and 16:
2 Ignition system Check the ignitio
Page 17 and 18:
2 Ignition system Fit piston stop N
Page 19 and 20:
2 Ignition system Fit the ignition
Page 21 and 22: 3 Fuel system In addition to the fu
Page 23 and 24: 15 10 5 20 0 100 50 0 150 30 200 25
Page 25 and 26: 3 Fuel system A Dismantle the screw
Page 27 and 28: 3 Fuel system Speed limiter Mod. 65
Page 29 and 30: 3 Fuel system In the event of leaka
Page 31 and 32: 3 Fuel system Assembly of the carbu
Page 33 and 34: 3 Fuel system Walbro WG 9 A C B Mod
Page 35 and 36: 3 Fuel system Fine adjustment of th
Page 37 and 38: 3 Fuel system Lift off the half of
Page 39 and 40: 3 Fuel system Mod. 1250 Separate th
Page 41 and 42: 3 Fuel system Trouble-shooting char
Page 43 and 44: 4 Centrifugal clutch The centrifuga
Page 45 and 46: 4 Centrifugal clutch Mod. 950, 1250
Page 47 and 48: 4 Centrifugal clutch The clutch dru
Page 49 and 50: 5 Cylinder and piston The cylinder
Page 51 and 52: 5 Cylinder and piston Unscrew the c
Page 53 and 54: 5 Cylinder and piston Piston seizur
Page 55 and 56: 5 Cylinder and piston Reasons: ●
Page 57 and 58: 5 Cylinder and piston Fit a new cyl
Page 59 and 60: 5 Cylinder and piston Check that th
Page 61 and 62: 6 Crankshaft and crankcase The purp
Page 63 and 64: 6 Crankshaft and crankcase Mod. 950
Page 65 and 66: 6 Crankshaft and crankcase Remove t
Page 67 and 68: 6 Crankshaft and crankcase Mod. 125
Page 69 and 70: 6 Crankshaft and crankcase Heat up
Page 71: 6 Crankshaft and crankcase M5 x 20
Page 75 and 76: 6 Model 950 - Crankcase lubrication
Page 78 and 79: Cutting equipment 7. Contents Disma
Page 80 and 81: Cutting equipment 7 Release the bel
Page 82 and 83: Cutting equipment 7 D E F Turn the
Page 84 and 85: Cutting equipment 7 B A Lift the cu
Page 86 and 87: Tools 8. Contents Clutch ..........
Page 88 and 89: Tools 8 Sealing ring Model 505 38 1
Page 90 and 91: 15 10 5 100 50 0 150 30 200 250 300
Page 92 and 93: Tools 8 Workshop equipment Model 3
Page 94 and 95: Technical data 9. Contents Technica
Page 96: 108 07 07-47 SEK 95:- Teknik-Info A
show all

WM, Workshop Manual, K650, K700, K950, K1250, 2001-06, Power ...

Create successful ePaper yourself

Delete template?

Save as template?