WM, Workshop Manual, K650, K700, K950, K1250, 2001-06, Power ...

More documents

Recommendations

Info

Cutting equipment 7 D E F Turn the guard while the other parts are held in place. Then install a plastic washer (C), the thin rubber washer (D), plastic washer (E), cover plate (F) and plastic cover (G). Tighten the three screws and check that the guard can be turned. C G 505 38 13-08 Press the shaft in through the ball bearings until it projects 5.5 mm from the ball bearing on the other side. Fit the belt wheel (reinforcement washer turned inwards). Do not forget the spacer ring against the ball bearings. Tighten the screw. Drive the shaft in through the ball bearings, using a plastic-faced hammer, until it projects 5.5 mm from the ball bearing on the other side. Fit the pulley. Place the spacer ring on the ball bearings and then put on the pulley with the welded reinforcement washer turned inwards towards the cutter arm. Tighten the screw. Fit the spacer sleeves and support washer as shown in the illustration. Heat the spacer sleeve outside the support washer with a hot air gun to approx. 150°C to simplify fitting it on the shaft. Press it down with a suitable drift (502 50 82-01). 502 50 82-01 81
7 Cutting equipment A. Inspect the drive belt for wear and damage before it is fitted. Fig. A. Normal condition of a belt after prolonged use. B. Fig. B. Replace the belt if after a short period of use it shows signs of cracking across the belt, even if there is only slight wear on the sides. C. D. Fig. C. Worn, rough edges on the belt are the result of incorrect contact with the pulley or loose nuts on the cutter arm. Fig. D. Irregular wear resulting from loose belt or high idling speed. E. Fig. E. Worn off strips of belt, worn reinforcement, resulting from poor contact, oil on the pulley, or incorrect belt quality. Use Partner Genuine Belts. Place a new drive belt round the clutch drum and it the clutch cover. Place a new drive belt round the clutch drum. Ffit the clutch cover. Do not forget the screw in the lower edge of the guard. 82
Page 1 and 2:
PARTNER Workshop Manual R
Page 3 and 4:
General recommendations Keep this i
Page 5 and 6:
1 Starter unit ! WARNING! When work
Page 7 and 8:
1 Starter unit Anchor the starter r
Page 9 and 10:
1 Starter unit Assembly Mod. 650, 7
Page 11 and 12:
1 Anchor the starter cord in the st
Page 13 and 14:
2 Ignition system The engine is fit
Page 15 and 16:
2 Ignition system Check the ignitio
Page 17 and 18:
2 Ignition system Fit piston stop N
Page 19 and 20:
2 Ignition system Fit the ignition
Page 21 and 22:
3 Fuel system In addition to the fu
Page 23 and 24:
15 10 5 20 0 100 50 0 150 30 200 25
Page 25 and 26:
3 Fuel system A Dismantle the screw
Page 27 and 28:
3 Fuel system Speed limiter Mod. 65
Page 29 and 30:
3 Fuel system In the event of leaka
Page 31 and 32: 3 Fuel system Assembly of the carbu
Page 33 and 34: 3 Fuel system Walbro WG 9 A C B Mod
Page 35 and 36: 3 Fuel system Fine adjustment of th
Page 37 and 38: 3 Fuel system Lift off the half of
Page 39 and 40: 3 Fuel system Mod. 1250 Separate th
Page 41 and 42: 3 Fuel system Trouble-shooting char
Page 43 and 44: 4 Centrifugal clutch The centrifuga
Page 45 and 46: 4 Centrifugal clutch Mod. 950, 1250
Page 47 and 48: 4 Centrifugal clutch The clutch dru
Page 49 and 50: 5 Cylinder and piston The cylinder
Page 51 and 52: 5 Cylinder and piston Unscrew the c
Page 53 and 54: 5 Cylinder and piston Piston seizur
Page 55 and 56: 5 Cylinder and piston Reasons: ●
Page 57 and 58: 5 Cylinder and piston Fit a new cyl
Page 59 and 60: 5 Cylinder and piston Check that th
Page 61 and 62: 6 Crankshaft and crankcase The purp
Page 63 and 64: 6 Crankshaft and crankcase Mod. 950
Page 65 and 66: 6 Crankshaft and crankcase Remove t
Page 67 and 68: 6 Crankshaft and crankcase Mod. 125
Page 69 and 70: 6 Crankshaft and crankcase Heat up
Page 71 and 72: 6 Crankshaft and crankcase M5 x 20
Page 73 and 74: 6 Crankshaft and crankcase Check th
Page 75 and 76: 6 Model 950 - Crankcase lubrication
Page 78 and 79: Cutting equipment 7. Contents Disma
Page 80 and 81: Cutting equipment 7 Release the bel
Page 84 and 85: Cutting equipment 7 B A Lift the cu
Page 86 and 87: Tools 8. Contents Clutch ..........
Page 88 and 89: Tools 8 Sealing ring Model 505 38 1
Page 90 and 91: 15 10 5 100 50 0 150 30 200 250 300
Page 92 and 93: Tools 8 Workshop equipment Model 3
Page 94 and 95: Technical data 9. Contents Technica
Page 96: 108 07 07-47 SEK 95:- Teknik-Info A
show all

WM, Workshop Manual, K650, K700, K950, K1250, 2001-06, Power ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?