WM, Workshop Manual, K650, K700, K950, K1250, 2001-06, Power ...

More documents

Recommendations

Info

10 5 50 Fuel system 3 Combinations of carburettors, induction pipe, seals, screwdriver guides K650 Active, K700 Active Carburettor Induct. pipe Seal Insert, seal Screwdriver guide HS175E 503 28 03-20 506 21 41-01 506 22 65-01 Black Not compensated Black Rubber foam, bonded to cyl. housing K650 Active II, K700 Active II Carburettor Induct. pipe Seal Insert, seal Screwdriver guide HS175F 503 28 04-03 506 21 41-01 506 25 34-01 506 25 33-01 Blue Compensated, blue insert Black Moulded Blue HS175G 503 28 04-04 506 21 41-01 506 25 34-01 506 25 33-01 Blue Compensated,blue insert Black Moulded Blue Small needle valve HS175G 503 28 04-08 506 26 72-01 506 26 85-01 – Comp., green insert, EPA Blue Moulded HS175L 503 28 04-15 506 31 16-01 506 26 85-01 – Comp., yellow insert, EPA Yellow Moulded Tower model HS175L, 503 28 04-16 506 31 16-01 506 26 85-01 Grey Comp., grey insert, EPA Grey Moulded Tower model There are different sizes and versions of carburettors on the different models, but in terms of servicing they are all treated in the same way. Dismantling of the carburettor Remove the screw driver guide and cover for the metering diaphragm. Check the diaphragm for damage. Replace if necessary. Dismantling of the carburettor Remove the screw driver guide over the adjusting screws. Remove the 4 screws for the metering diaphragm cover. Lift off the compensation insert and the diaphragm. Check the diaphragm for holes and wear. Replace the diaphragm if necessary. Pressure test the metering system. Connect pressure tester 501 56 27-01 to the fuel pipe nipple. Submerge the carburettor in a basin with petrol to simplify inspection for leaks. Pressure test with 0.5 bar. No leakage is permissible. 30 200 150 250 15 100 300 350 50 400 0 20 0 25 35 40 60 45 55 501 56 27-01 27
3 Fuel system In the event of leakage - dismantle the needle valve. In the event of leakage dismantle the needle valve. Release the screw and lift off the lever, shaft, needle valve and spring. Check the needle valve and lever for wear. Replace damaged parts with new ones. Check the needle valve for damage at the point and the groove for the lever. Check the lever for wear in the grooves for the needle valve and the diaphragm. Replace damaged parts with new ones. If the new needle valve also leaks the fault may be that the seat for the valve is damaged. Remove the pump diaphragm. Check the diaphragm for damage. Remove the screws which hold the cover over the pump diaphragm. Lift off the cover, gasket and diaphragm. Check the diaphragm for damage on the valve tongues. Hold it up to a lamp to inspect for holes in the material. Remove the fuel strainer. Carefully remove the fuel strainer, e.g. by using a needle. 28
Page 1 and 2: PARTNER Workshop Manual R
Page 3 and 4: General recommendations Keep this i
Page 5 and 6: 1 Starter unit ! WARNING! When work
Page 7 and 8: 1 Starter unit Anchor the starter r
Page 9 and 10: 1 Starter unit Assembly Mod. 650, 7
Page 11 and 12: 1 Anchor the starter cord in the st
Page 13 and 14: 2 Ignition system The engine is fit
Page 15 and 16: 2 Ignition system Check the ignitio
Page 17 and 18: 2 Ignition system Fit piston stop N
Page 19 and 20: 2 Ignition system Fit the ignition
Page 21 and 22: 3 Fuel system In addition to the fu
Page 23 and 24: 15 10 5 20 0 100 50 0 150 30 200 25
Page 25 and 26: 3 Fuel system A Dismantle the screw
Page 27: 3 Fuel system Speed limiter Mod. 65
Page 31 and 32: 3 Fuel system Assembly of the carbu
Page 33 and 34: 3 Fuel system Walbro WG 9 A C B Mod
Page 35 and 36: 3 Fuel system Fine adjustment of th
Page 37 and 38: 3 Fuel system Lift off the half of
Page 39 and 40: 3 Fuel system Mod. 1250 Separate th
Page 41 and 42: 3 Fuel system Trouble-shooting char
Page 43 and 44: 4 Centrifugal clutch The centrifuga
Page 45 and 46: 4 Centrifugal clutch Mod. 950, 1250
Page 47 and 48: 4 Centrifugal clutch The clutch dru
Page 49 and 50: 5 Cylinder and piston The cylinder
Page 51 and 52: 5 Cylinder and piston Unscrew the c
Page 53 and 54: 5 Cylinder and piston Piston seizur
Page 55 and 56: 5 Cylinder and piston Reasons: ●
Page 57 and 58: 5 Cylinder and piston Fit a new cyl
Page 59 and 60: 5 Cylinder and piston Check that th
Page 61 and 62: 6 Crankshaft and crankcase The purp
Page 63 and 64: 6 Crankshaft and crankcase Mod. 950
Page 65 and 66: 6 Crankshaft and crankcase Remove t
Page 67 and 68: 6 Crankshaft and crankcase Mod. 125
Page 69 and 70: 6 Crankshaft and crankcase Heat up
Page 71 and 72: 6 Crankshaft and crankcase M5 x 20
Page 73 and 74: 6 Crankshaft and crankcase Check th
Page 75 and 76: 6 Model 950 - Crankcase lubrication
Page 78 and 79:
Cutting equipment 7. Contents Disma
Page 80 and 81:
Cutting equipment 7 Release the bel
Page 82 and 83:
Cutting equipment 7 D E F Turn the
Page 84 and 85:
Cutting equipment 7 B A Lift the cu
Page 86 and 87:
Tools 8. Contents Clutch ..........
Page 88 and 89:
Tools 8 Sealing ring Model 505 38 1
Page 90 and 91:
15 10 5 100 50 0 150 30 200 250 300
Page 92 and 93:
Tools 8 Workshop equipment Model 3
Page 94 and 95:
Technical data 9. Contents Technica
Page 96:
108 07 07-47 SEK 95:- Teknik-Info A
show all

WM, Workshop Manual, K650, K700, K950, K1250, 2001-06, Power ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?