WM, Workshop Manual, K650, K700, K950, K1250, 2001-06, Power ...

More documents

Recommendations

Info

Crankshaft and crankcase 6 A Mod. 1250 Vibration damper at cylinder Remove the screws (A) and (B). Mod. 1250 Vibration damper at cylinder 1. Remove the screw (A) which holds the damper to the grip. 2. Remove the screws (B) which hold the grip to the tank unit. B 502 50 18-01 Unscrew the vibration damper. 3. Turn the grip so that the vibration damper can be unscrewed with tool 502 50 66-02. NOTE! Make sure that the tool grips both the vibration damper’s metal plates. Fit new vibration damper in the reverse order to dismantling. 502 50 66-02 Mod. 1250 Front vibration damper Remove the screws (A) and (B). Mod. 1250 Front vibration damper 1. Remove screws (A) and (B). B A Separate crankcase and tank unit and remove the screw which holds the vibration damper. 2. Separate crankcase and tank unit sufficiently to allow the screw which holds the vibration damper to be removed. Fit in the reverse order to dismantling. 502 50 18-01 65
6 Crankshaft and crankcase Mod. 1250 Rear vibration damper Dismantle the starter unit and the two screws which hold the rear, upper vibration dampers. Remove also the screw which holds the vibration damper at the grip. Mod. 1250 Rear vibration damper 1. Dismantle the starter unit. 2. Remove the two screws which hold the rear, upper vibration dampers. 3. Remove also the screw which hold the vibration damper at the grip to simplify separation of the engine and tank unit. 502 50 64-01 Remove the screw which holds the lower vibration damper and separate crankcase and tank unit so that the damper can be unscrewed with tool 502 50 66-02. 4. Remove the screw which holds the lower vibration damper. 5. Separate crankcase and tank unit sufficiently to allow tool 502 50 66-02 to be placed over the vibration damper. 6. Unscrew the damper and replace it with a new one. NOTE! The tool should grip the damper’s two metal plates. 502 50 66-02 Dismantle the two upper vibration dampers. 7. Dismantle the two upper vibration dampers. Insert key No. 502 50 18-01 in the damper and unscrew the screw. Lift off the damper. Fit in the reverse order to dismantling. A A A 502 50 18-01 Dismantling, assembly Mod. 650, 700 Remove the washer which lies inside the clutch drum and the screws (A). Dismantling, assembly Mod. 650, 700 Dismantle all parts, including the fuel tank, so that only the handle unit and crankcase remain. Remove the washer which lies inside the clutch drum (see chapter ”Replacing the seal on the clutch side”). Remove the screws (A). A 505 38 13-08 66
Page 1 and 2:
PARTNER Workshop Manual R
Page 3 and 4:
General recommendations Keep this i
Page 5 and 6:
1 Starter unit ! WARNING! When work
Page 7 and 8:
1 Starter unit Anchor the starter r
Page 9 and 10:
1 Starter unit Assembly Mod. 650, 7
Page 11 and 12:
1 Anchor the starter cord in the st
Page 13 and 14:
2 Ignition system The engine is fit
Page 15 and 16: 2 Ignition system Check the ignitio
Page 17 and 18: 2 Ignition system Fit piston stop N
Page 19 and 20: 2 Ignition system Fit the ignition
Page 21 and 22: 3 Fuel system In addition to the fu
Page 23 and 24: 15 10 5 20 0 100 50 0 150 30 200 25
Page 25 and 26: 3 Fuel system A Dismantle the screw
Page 27 and 28: 3 Fuel system Speed limiter Mod. 65
Page 29 and 30: 3 Fuel system In the event of leaka
Page 31 and 32: 3 Fuel system Assembly of the carbu
Page 33 and 34: 3 Fuel system Walbro WG 9 A C B Mod
Page 35 and 36: 3 Fuel system Fine adjustment of th
Page 37 and 38: 3 Fuel system Lift off the half of
Page 39 and 40: 3 Fuel system Mod. 1250 Separate th
Page 41 and 42: 3 Fuel system Trouble-shooting char
Page 43 and 44: 4 Centrifugal clutch The centrifuga
Page 45 and 46: 4 Centrifugal clutch Mod. 950, 1250
Page 47 and 48: 4 Centrifugal clutch The clutch dru
Page 49 and 50: 5 Cylinder and piston The cylinder
Page 51 and 52: 5 Cylinder and piston Unscrew the c
Page 53 and 54: 5 Cylinder and piston Piston seizur
Page 55 and 56: 5 Cylinder and piston Reasons: ●
Page 57 and 58: 5 Cylinder and piston Fit a new cyl
Page 59 and 60: 5 Cylinder and piston Check that th
Page 61 and 62: 6 Crankshaft and crankcase The purp
Page 63 and 64: 6 Crankshaft and crankcase Mod. 950
Page 65: 6 Crankshaft and crankcase Remove t
Page 69 and 70: 6 Crankshaft and crankcase Heat up
Page 71 and 72: 6 Crankshaft and crankcase M5 x 20
Page 73 and 74: 6 Crankshaft and crankcase Check th
Page 75 and 76: 6 Model 950 - Crankcase lubrication
Page 78 and 79: Cutting equipment 7. Contents Disma
Page 80 and 81: Cutting equipment 7 Release the bel
Page 82 and 83: Cutting equipment 7 D E F Turn the
Page 84 and 85: Cutting equipment 7 B A Lift the cu
Page 86 and 87: Tools 8. Contents Clutch ..........
Page 88 and 89: Tools 8 Sealing ring Model 505 38 1
Page 90 and 91: 15 10 5 100 50 0 150 30 200 250 300
Page 92 and 93: Tools 8 Workshop equipment Model 3
Page 94 and 95: Technical data 9. Contents Technica
Page 96: 108 07 07-47 SEK 95:- Teknik-Info A
show all

WM, Workshop Manual, K650, K700, K950, K1250, 2001-06, Power ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?