PT-600 Mechanized Plasma Cutting Torch
PT-600 Mechanized Plasma Cutting Torch
PT-600 Mechanized Plasma Cutting Torch
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
SECTION 4<br />
OPERATION<br />
CUTTING PARAMETERS FOR THE ESP-150 & ESP-200<br />
Table 4-1. 50 - 65 Amp Data<br />
Nozzle - 50 Amp P/N 0558001881<br />
Electrode - Hafnium P/N 0558001624<br />
Gas Baffle - 4 hole P/N 0558002533<br />
Shield - 50 Amp P/N 21795<br />
Diffuser - 50 Amp P/N 21796<br />
Pilot Arc - LOW<br />
Material<br />
Type-Thickness<br />
in.(mm)<br />
Current<br />
(Amps)<br />
Travel<br />
Speed<br />
ipm(m/min)<br />
Pierce<br />
Height<br />
in. (mm)<br />
<strong>Cutting</strong><br />
Height<br />
in.(mm)<br />
Arc<br />
Voltage<br />
(Volts)<br />
CS - 1/16 (1.6) 50 220 (5.6) 1/4 (6.4) 5/32 (4) 115 Air - 40 (2.76) Air - 60 (4.14) Air - 30 (2.07)<br />
CS - 1/8 (3.2) 120 (3) 112<br />
CS - 1/8 (3.2) 65 120 (3) 1/8 (3.2) 110<br />
CS - 3/16 (4.8) 95 (2.4) 5/32 (4) 118<br />
CS - 1/4 (6.4) 80 (2) 120 Air - 65 (4.48)<br />
CS - 3/8 (9.6) 40 (2) 5/16 (8) 122<br />
SS - 1/16 (1.6) 50 180 (4.6) 1/4 (6.4) 5/32 (4) 111 Air - 40 (2.76) Air - 60 (4.14) Air - 30 (2.07)<br />
SS - 1/8 (3.2) 65 80 (2) 119<br />
SS - 1/4 (6.4) 60 (1.5) 118 Air - 65 (4.48)<br />
AL - 1/16 (1.6) 50 180 (4.6) 1/4 (6.4) 1/8 (3.2) 116 Air - 40 (2.76) Air - 60 (4.14) Air - 45 (3.1)<br />
AL - 1/8 (3.2) 110 (2.8) 115<br />
AL - 1/4 (6.4) 65 65 (1.6) 5/32 (4) 128 Air - 65 (4.48)<br />
AL - 1/16 (1.6) 50 180 (4.6) 1/4 (6.4) 1/8 (3.2) 118 N 2<br />
- 40 (2.76) N 2<br />
- 60 (4.14) N 2<br />
- 30 (2.07)<br />
AL - 1/8 (3.2) 120 (3) 117<br />
Start Gas<br />
Type/Pressure<br />
psi (bar)<br />
<strong>Plasma</strong> Gas<br />
Type/Pressure<br />
psi (bar)<br />
Shield Gas<br />
Type/Pressure<br />
psi (bar)<br />
*<br />
AL - 1/4 (6.4) 65 70 (1.8) 125 N 2<br />
- 65 (4.48)<br />
SS - 1/16 (1.6) 50 180 (4.6) 1/4 (6.4) 5/32 (4) 119 N 2<br />
- 40 (2.76) N 2<br />
- 60 (4.14) N 2<br />
- 30 (2.07)<br />
SS - 1/8 (3.2) 65 80 (2) 125 N 2<br />
- 45 (3.1)<br />
SS - 1/4 (6.4) 55 (1.4) 127 N 2<br />
- 65 (4.48)<br />
NOTES:<br />
CS - Carbon Steel, SS - Stainless Steel, AL - Aluminum<br />
Air <strong>Plasma</strong>/Air Shield, 50 - 65 Amp cuts on Stainless Steel and Aluminum have rough surfaces.<br />
N 2<br />
<strong>Plasma</strong>/N 2<br />
Shield, 50 - 65 Amp cuts of Stainless Steel and Aluminum have fair to good surfaces.<br />
* - uses electrode p/n 0558002499<br />
4-insert
Change language